Fluke Welder PN 643657 User Manual

®
16  
Multimeter with Temperature  
Instruction Sheet  
P
Read First: Safety Information  
To ensure that the meter is used safely, follow these instructions:  
Do not use the meter if the meter or test leads appear damaged, or if  
you suspect that the meter is not operating properly.  
Disconnect the live test lead before disconnecting the common test  
lead.  
When using the probes, keep your fingers behind the finger guards on  
the probes.  
Do not use the VCheck mode to measure voltages in circuits that  
could be damaged by this mode’s low input impedance  
(2 k).  
Turn off power to the circuit under test before cutting, desoldering, or  
breaking the circuit. Small amounts of current can be dangerous.  
Do not apply more than 600V rms between a meter terminal and earth  
ground.  
Use caution when working with voltages above 60V dc or 30V ac rms.  
Such voltages pose a shock hazard.  
PN 643657 June 1997 Rev.2, 3/98  
1997, 1998 Fluke Corporation. All rights reserved. Printed in U.S.A.  
 
AC and DC Voltage  
Also refer to VCheck.  
Volts AC  
Input Impedance 5 MΩ  
50 Hz to 400 Hz  
Volts DC  
Input Impedance 10 MΩ  
MULTIMETER  
MULTIMETER  
16  
16  
AC  
DC  
4000 mV 4V 40V 400V 600V  
OFF  
OFF  
V
AC DC  
V
AC  
/
DC  
/
CAT  
CAT  
600V  
600V  
COM  
+
COM  
+
ip01i.eps  
Resistance and Continuity eR  
Turn off circuit power before testing. Also refer to VCheck.  
Resistance  
Continuity  
16  
MULTIMETER  
MULTIMETER  
MULTIMETER  
16  
16  
Mk  
OFF  
OFF  
OFF  
V
Check  
V
Check  
VCheck  
A
Low Impedance  
V•Check  
A
A
CAT  
CAT  
CAT  
TEMPERATURE  
TEMPERATURE  
TEMPERATURE  
600V  
600V  
600V  
COM  
+
COM  
+
COM  
+
4004 k40 k400 k4 m40 mΩ  
Detects shorts and opens 250 µS.  
Short  
Open  
<25Ω  
ip02i.eps  
 
W VCheck  
If a dc or ac voltage greater than about 4.5V is present across the inputs  
when the meter is set to R, G, or e, the meter switches automatically  
to dc or ac voltage mode (VCheck mode).  
W Warning  
Repetitive transients on a dc bus will cause VCheck to  
select ac volts, even though a hazardous dc voltage may  
be present. To avoid a misleading display and possible  
electric shock, manually select the proper volts function  
for measurements on these circuits.  
When VCheck is activated, the meter has low input impedance (LoZ)  
2 k. This load can alter the voltages in electronic control circuits. Do  
not use VCheck to measure voltage in circuits that could be damaged by  
a 2 kload.  
Hint: VCheck can be effectively used to eliminate “ghost” voltages.  
Disable and re-enable V•Check  
For and ,  
If AC detected  
If DC detected  
MULTIMETER  
16  
,
Disables V•Check and  
locks meter in selected  
mode.  
Meter puts 2 kΩ  
load on circuit.  
2 sec  
OFF  
V
Check  
A
CAT  
TEMPERATURE  
600V  
or  
or  
COM  
+
Re-enables  
V•Check  
or  
ip09i.eps  
 
Temperature  
MULTIMETER  
16  
°F  
°C  
OFF  
VCheck  
A
CAT  
TEMPERATURE  
600V  
COM  
+
Vent  
or  
Pipe  
80PK-1 Type K  
Thermocouple  
Probe  
ip19f.eps  
Note correct connector polarity.  
To meet stated accuracy, the 80AK temperature adapter must be at the  
same temperature as the meter. In addition, the 80AK and the 80PK-1  
should be cleaned and lubricated regularly. Use any petroleum based  
lubricant.  
Warning  
To avoid possible electric shock, DO NOT apply  
thermocouple tip to any conductor that is greater than  
30V AC, 42.4V pk, or 60V DC to earth.  
 
Capacitance E  
Turn off circuit power; then disconnect and discharge the capacitor before  
measuring capacitance.  
MULTIMETER  
16  
If the capacitor requires more  
discharging, diSC is displayed  
while the capacitor discharges.  
OFF  
V
Check  
A
CAT  
TEMPERATURE  
600V  
COM  
+
1 µF 10 µF  
100 µF  
10,000 µF  
+
ip05i.eps  
Note correct probe polarity for polarized capacitors.  
 
Microamps µA  
Range 0 to 200 µA  
MULTIMETER  
16  
µA AC  
µA DC  
OFF  
V
Check  
A
CAT  
TEMPERATURE  
600V  
COM  
+
Flame  
sensor  
probe  
Control  
module  
ip20i.eps  
Example: Flame rectification circuit.  
 
Diode Test G  
Turn off circuit power before testing. For best results diodes  
should be measured out of circuit.  
Also refer to VCheck.  
Good Diode  
MULTIMETER  
Typical voltage  
for silicon diode  
MULTIMETER  
16  
16  
Low Impedance  
V•Check  
OFF  
OFF  
V
Check  
VCheck  
A
A
CAT  
CAT  
TEMPERATURE  
TEMPERATURE  
600V  
600V  
COM  
+
COM  
+
Single beep  
ip03i.eps  
Forward Bias  
Reverse Bias  
Bad Diode  
MULTIMETER  
16  
MULTIMETER  
16  
OFF  
OFF  
VCheck  
VCheck  
A
A
CAT  
TEMPERATURE  
CAT  
TEMPERATURE  
600V  
600V  
COM  
+
COM  
+
or  
ip04i.eps  
Shorted  
Open  
 
µF  
MIN MAX  
(Records the lowest and highest measurements)  
VCheck, autoranging, and Battery Saver are disabled. Put the meter  
in the proper range before entering MIN MAX.  
When the reading changes more than about 50 digits, the meter gives a  
short beep. When a new minimum or maximum is recorded, the meter  
gives a long beep.  
Enter  
MIN MAX  
Present Reading with  
Input Change AlertTM  
Maximum Reading  
2 sec  
To Exit  
Minimum Reading  
ip10i.eps  
 
µF  
MIN MAX with Elapsed Time  
Records the hours and minutes between when MIN MAX was entered  
and the last high and low was recorded. OL is displayed for times longer  
than 99:59.  
To enable the MIN MAX timer, hold down M while turning the rotary  
switch from OFF to either measurement mode.  
Enter MIN MAX. View Maximum Reading  
Present Reading  
Maximum Reading  
Elapsed Time  
2 sec  
Minimum Reading  
Elapsed Time  
Minimum Reading  
Exit MIN MAX  
ip11i.eps  
 
Disabling the Beeper  
To disable the beeper for all modes, hold down r for 2 seconds while  
turning the meter on.  
Continuity Capture  
To set up the meter to capture intermittent shorts and opens, turn the  
switch to GR, connect the leads to the circuit; then press M.  
ip12i.eps  
Captures transitions longer than 250 µs (1/4000th of a second).  
Transitions after the first transition cause the meter to beep, but the  
display does not change.  
To reset the display to the current condition, press M.  
To exit, press M for 2 seconds, or change the measurement mode.  
 
Maintenance  
Clean the case with a damp cloth and detergent. Do not use abrasives or  
solvents.  
Battery Replacement  
Remove the test leads before disassembling the case.  
COM  
600V  
+
+
ip13i.eps  
Replacement Parts  
Fluke TL-75 (Double-insulated leads)  
80AK-8001 (Adapter, Thermocouple)  
80PK-1 (Probe, Thermocouple, Beaded K-Type)  
PN 855705  
PN 919683  
PN 750422  
Service and Parts  
This meter should be serviced only by a qualified service technician. For  
service information in the USA and Canada call 1-800-526-4731. To  
locate an authorized service center, visit us on the World Wide Web:  
www.fluke.com or call Fluke using any of the phone numbers listed  
below.  
USA and Canada: 1-800-44-FLUKE (1-800-443-5853)  
Europe: +31 402-678-200  
Japan: +81-3-3434-0181  
Singapore: +65- -276-6196  
*
Anywhere in the world: +1-425-356-5500  
 
Specifications  
Accuracy is specified for a period of one year after calibration, at 18°C to  
28°C (64°F to 82°F) with relative humidity to 90%. AC conversions are  
ac-coupled, average responding, and calibrated to the rms value of a sine  
wave input. Accuracy specifications are given as follows:  
±([% of reading] + [number of least significant digits])  
Function  
Range  
Resolution  
Accuracy  
-10°C to 400°C  
14°F to 752°F  
0.1°C or  
0.2°F  
±(1.0% + 0.8°C)  
typical  
Temperature  
±(1.0% + 1.5°F) typical  
±(5.0% + 1.5°C)  
typical  
(Type K Thermocouple) -40°C to -10°C  
-40°F to 14°F  
0.1°C or  
0.2°F  
±(5.0% + 3.3°F) typical  
Error does not include Type K Thermocouple errors.  
Function  
Range  
Resolution  
Accuracy  
4000 mV1  
4.000V  
1 mV  
±(1.9% + 3)  
±(1.9% + 3)  
±(1.9% + 3)  
±(1.9% + 3)  
±(1.9% + 3)  
±(0.9% + 2)  
±(0.9% + 2)  
±(0.9% + 1)  
±(0.9% + 1)  
0.001V  
00.01V  
000.1V  
1V  
40.00V  
400.0V  
(50 to 400 Hz)  
600V  
4000 mV1  
4.000V  
1 mV  
0.001V  
00.01V  
000.1V  
1V  
40.00V  
400.0V  
600V  
±(0.9% + 1)  
400.0Ω  
0.1Ω  
±(0.9% + 2)  
±(0.9% + 1)  
±(0.9% + 1)  
±(0.9% + 1)  
±(0.9% + 1)  
±(1.5% + 3)  
±(1.9% + 2)  
±(1.9% + 2)  
4.000 kΩ  
40.00 kΩ  
400.0 kΩ  
4.000 MΩ  
40.00 MΩ  
1.000 µF  
10.00 µF  
100.0 µF  
10000 µF  
0.001 kΩ  
0.01 kΩ  
0.1 kΩ  
0.001 MΩ  
0.01 MΩ  
0.001 µF  
0.01 µF  
0.1 µF  
1 µF  
±(1.9% + 2)  
1000 µF ±(1.9% + 2)  
>1000 µF ±(10% + 90) typical  
±(1.9% + 2)2  
2.000V  
0.001V  
1.The 4000 mV range can be entered only in manual range mode. Use the  
4000 mV range with accessories.  
2.The beeper is guaranteed to come on at <25and turn off at >250. The  
meter detects opens or shorts 250 µs.  
 
Function  
Range Resolution  
Accuracy  
Burden Voltage  
0 to 200 µA  
0 to 200 µA  
0.1 µA  
0.1 µA  
±(2% + 3 counts)  
<5 mV/µA  
(50 Hz to 400  
Hz)  
±(1% + 2 counts)  
<5 mV/µA  
Overload  
Function  
Input Impedance (Nominal)  
Protection1  
>5 M<100 pF  
600V rms  
VCheck and LoZ = >2 k<200 pF (ac coupled)2  
>10M<100 pF  
600V rms  
VCheck and LoZ = >2 k<200 pF2  
Common Mode Rejection  
Normal Mode Rejection  
Ratio (1 kUnbalanced)  
600V rms >60 dB at dc 50 or 60 Hz  
600V rms >100 dB at dc, 50 or 60 Hz >50 dB at 50 Hz or 60 Hz  
Full Scale Voltage  
Open Circuit Test Voltage  
To 4.0 MΩ  
40 MΩ  
600V rms  
600V rms  
<1.5V dc  
<450 mV dc <1.5V dc  
2.4-3.0V dc  
2.400V dc  
Short Circuit Current  
600V rms  
600V rms  
<500 µA  
0.95 mA (typical)  
1. 3 x 106 V Hz maximum  
2. 2 kinput impedance up to 50V. Impedance increases with input voltage to  
>300 kat 600V.  
MIN MAX Recording Accuracy and Response Time  
Specified accuracy of the measurement function ±12 digits in dc for changes  
>200 ms in duration (±40 digits in ac). Typical 100 ms response to 80%.  
Example 1: This would mean ±1.2° when recording temperature.  
Example 2: This would mean ±12 µA when recording µA or ±12A if used with a  
dc amp probe (with a mV input).  
 
MIN MAX Recording with Elapsed Time  
Elapsed Time  
Resolution  
Accuracy  
0 to 100 hours (99:59)  
1 minute  
0.3% typical  
Maximum Voltage  
Between any Terminal  
and Earth Ground:  
600V rms  
Display:  
3 3/4-digits, 4000 counts, updates 4/sec  
Operating Temperature: -10°C to 50°C (14°F to 122°F)  
Storage Temperature:  
-30°C to 60°C (-22°F to 140°F)  
indefinitely (to -40°C (-40°F) for 100 hrs)  
Temperature  
Coefficient:  
(.1 x specified accuracy)/°C (<18°C or  
>28°C)  
Relative Humidity:  
0% to 90% (-10°C to 35°C; 14°F to 95°F)  
0% to 70% (35°C to 50°C; 95°F to 122°F)  
9V, NEDA 1604 or IEC 6F22  
650 continuous hours with alkaline  
450 continuous hours with carbon-zinc  
3 meter drops.  
Battery Type:  
Battery Life:  
Shock, Vibration:  
Size (H x W x L):  
3.46 cm x 7.05 cm x 14.23 cm  
(1.35 in x 2.75 in x 5.55 in)  
Weight:  
Safety:  
286g (10 oz)  
Designed to Protection Class II  
requirement of UL1244, ANSI/ISA-S82,  
CSA C22.2 No 231, and VDE 0411, and  
IEC 1010 overvoltage Category III (CAT  
III, 600 Volts).  
EMI Regulations:  
Certifications:  
Complies with FCC Part 15, Class B, and  
VDE 0871B. Trademark of TÜV Product  
Services. Complies with EN 61010-1:  
1993.  
TUV, UL and VDE pending  
 
LIMITED WARRANTY & LIMITATION OF LIABILITY  
Each Fluke product is warranted to be free from defects in material and workmanship under  
normal use and service. The warranty period is three years and begins on the date of shipment.  
Parts, product repairs and services are warranted for 90 days. This warranty extends only to the  
original buyer or end-user customer of a Fluke authorized reseller, and does not apply to fuses,  
disposable batteries or to any product which, in Fluke’s opinion, has been misused, altered,  
neglected or damaged by accident or abnormal conditions of operation or handling. Fluke  
warrants that software will operate substantially in accordance with its functional specifications for  
90 days and that it has been properly recorded on non-defective media. Fluke does not warrant  
that software will be error free or operate without interruption.  
Fluke authorized resellers shall extend this warranty on new and unused products to end-user  
customers only but have no authority to extend a greater or different warranty on behalf of Fluke.  
Warranty support is available if product is purchased through a Fluke authorized sales outlet or  
Buyer has paid the applicable international price. Fluke reserves the right to invoice Buyer for  
importation costs of repair/replacement parts when product purchased in one country is submitted  
for repair in another country.  
Fluke’s warranty obligation is limited, at Fluke’s option, to refund of the purchase price, free of  
charge repair, or replacement of a defective product which is returned to a Fluke authorized  
service center within the warranty period.  
To obtain warranty service, contact your nearest Fluke authorized service center or send the  
product, with a description of the difficulty, postage and insurance prepaid (FOB Destination), to  
the nearest Fluke authorized service center. Fluke assumes no risk for damage in transit.  
Following warranty repair, the product will be returned to Buyer, transportation prepaid (FOB  
Destination). If Fluke determines that the failure was caused by misuse, alteration, accident or  
abnormal condition of operation or handling, Fluke will provide an estimate of repair costs and  
obtain authorization before commencing the work. Following repair, the product will be returned to  
the Buyer transportation prepaid and the Buyer will be billed for the repair and return  
transportation charges (FOB Shipping Point).  
THIS WARRANTY IS BUYER’S SOLE AND EXCLUSIVE REMEDY AND IS IN LIEU OF ALL  
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY  
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  
FLUKE SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR  
CONSEQUENTIAL DAMAGES OR LOSSES, INCLUDING LOSS OF DATA, WHETHER  
ARISING FROM BREACH OF WARRANTY OR BASED ON CONTRACT, TORT, RELIANCE OR  
ANY OTHER THEORY.  
Since some countries or states do not allow limitation of the term of an implied warranty, or  
exclusion or limitation of incidental or consequential damages, the limitations and exclusions of  
this warranty may not apply to every buyer. If any provision of this Warranty is held invalid or  
unenforceable by a court of competent jurisdiction, such holding will not affect the validity or  
enforceability of any other provision.  
Fluke Corporation  
P.O. Box 9090  
Everett WA  
Fluke Europe B.V.  
P.O. Box 1186  
5602 B.D. Eindhoven  
The Netherlands  
98206-9090  
5/94  
 

Electro Voice Music Mixer BK 1632 User Manual
Electro Voice Portable Speaker E V ELEVEN A User Manual
Festool Biscuit Joiner PD574447 User Manual
Finisar Network Card FTLF1217P2XTL User Manual
Frigidaire Air Conditioner FRA065AT7 User Manual
Galaxy Metal Gear Microwave Oven 87040 User Manual
GE Freezer GLD6700 60N User Manual
Gemini CD Player MPX 3 User Manual
GE Oven 106611 User Manual
Goodman Mfg Air Cleaner GDMHEPA User Manual