Flaircomm Technologies GPS Receiver GPSBT560 User Manual

GPSBT560 User Manual  
GPS Bluetooth Receiver User Manual  
ModelGPSBT560  
.
1
 
GPSBT560 User Manual  
radio communications. However, there is no guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference to radio or television reception, which can be  
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by  
one or more of the following measures:  
-Reorient or relocate the receiving antenna.  
-Increase the separation between the equipment and receiver.  
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
-Consult the dealer or an experienced radio/ TV technician for help.  
CAUTION:  
Any changes or modifications not expressly approved by the grantee of this device could void the user's  
authority to operate the equipment.  
RF exposure warning ·  
This equipment must be installed and operated in accordance with provided instructions and the antenna(s)  
used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons  
and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users  
and installers must be provide with antenna installation instructions and transmitter operating conditions  
for satisfying RF exposure compliance.  
CE command  
Bluetooth: ETSI EN 300 328 V1.6.1(2004-11); ETSI EN 301 489-1 V1.6.1(2005-09); ETSI EN 301 489-7  
V1.2.1(2002-08)  
GPS: ETSI EN 301 489-1 V1.6.1(2005-09); ETSI EN 301 489-19 V1.2.2(2002-11); ETSI EN 300 400-1  
V1.3.1(2001-09); ETSI EN 300 440-2 V1.1.2(2004-07)  
Safety: EN 60950-1:2006  
.
3
 
GPSBT560 User Manual  
1. INTRODUCTION.................................................................................................................................5  
1.1  
1.2  
1.3  
1.4  
1.5  
1.6  
GLOBAL POSITION SYSTEM (GPS) TECHNOLOGY ................................................................................5  
BLUETOOTH TECHNOLOGY ..................................................................................................................5  
INTELLIGENT GPS TRACKING AND BLUETOOTH CONNECTING (ITC) MANAGER..................................5  
PRODUCT FEATURES ............................................................................................................................6  
PACKAGE CONTENTS............................................................................................................................6  
OVERVIEW ...........................................................................................................................................7  
2. USING YOUR GPSBT560 RECEIVER..............................................................................................8  
2.1  
2.1.1  
2.1.2  
2.2  
2.3  
2.4  
2.5  
BATTERY CHARGING AND USAGE ........................................................................................................8  
Battery Charging .........................................................................................................................8  
Battery Information .....................................................................................................................8  
CONNECTING AN EXTERNAL ANTENNA.................................................................................................9  
PLACING THE RECEIVER .......................................................................................................................9  
SWITCHING THE RECEIVER ON AND OFF................................................................................................9  
PAIRING AND CONNECTING THE GPS RECEIVER WITH BLUETOOTH DEVICES......................................9  
Pairing the receiver with a Bluetooth device...............................................................................9  
Connecting/Disconnecting the receiver with a Bluetooth device ..............................................10  
2.5.1  
2.5.2  
3. IMPORTANT MESSAGES AND FREQUENTLY ASKED QUESTIONS...................................11  
4. MAINTENANCE ................................................................................................................................12  
.
4
 
GPSBT560 User Manual  
1. Introduction  
Combining both GPS and Bluetooth technologies, Flaircomm’s GPSBT560 receiver allows you to determine your  
current geographic location and direction anywhere. It communicates in real-time with Bluetooth-enabled devices  
such as PDAs, Smart Phones, Computers, and other devices to provide locations information for navigation  
applications. This battery-powered portable device can be easily placed on the car or carried by the user.  
1.1 Global Position System (GPS) Technology  
The Global Positioning System (GPS) is a worldwide radio-navigation system formed from a constellation of 24  
satellites and their ground stations. A GPS receiver is a device that calculates its location based on received satellite  
information and could provide its geographic location information with accuracy up to few meters. The accuracy of  
the receiver depends on the number of satellites in view and signal strengths received.  
1.2 Bluetooth Technology  
Bluetooth is an internationally standardized technology supporting short distance wireless communications. Any  
two Bluetooth-compatible equipments, such as mobile phone, PDA, PC, headset, mouse, keyboards, printer, etc.  
can wirelessly communicate with each other via Bluetooth connection. To ensure worldwide compatibility,  
Bluetooth operates on the globally available ISM (Industrial Scientific and Medical) frequency band. Within 2.4  
GHz and 2.48 GHz, Bluetooth transmits data up to either 10 meters (CLASS II mode) or 100 meters (CLASS I  
mode) using 79 frequency hopping channels.  
Though line-of-sight is not required, Bluetooth connections could be subject to interferences from obstructions such  
as walls, human bodies, and other electronic devices. In addition, due to variations on product implementation, it is  
likely that Bluetooth equipments from different manufactures have interoperability issues. In that case, you may  
consult with manufactures to check product compatibility.  
Note that, there could be some restrictions imposing on using Bluetooth devices in some countries. Please check  
with your local authorities.  
1.3 Intelligent GPS Tracking and Bluetooth Connecting (ITC) manager  
GPSBT560 is designed with advanced power management scheme, the intelligent GPS Tracking and Bluetooth  
Connecting (ITC) manager. The ITC manager automatically wakes up and goes to sleep depending on whether or  
not the Bluetooth connection is on. Once a paired Bluetooth device moves in the Bluetooth range and connects to  
the receiver, the ITC manager wakes up the GPS unit and commands it to start position tracking. Once a connected  
device moves out of the Bluetooth range or is disconnected by the user, the ITC manager shutdowns unused  
hardware components and commands the device entering into the sleeping mode. Thus minimizes GPSBT560’s  
power consumption and extends working and standby time dramatically.  
.
5
 
GPSBT560 User Manual  
1.4 Product Features  
z
GPS  
Compact GPS Bluetooth receiver with completed GPS functionality  
Compatible with any GPS navigation software using NMEA-0183 (V3.1) standard format GPS data  
16 C/A-code tracking modules with 4 correlators each  
Default (None) or Programmable WAAS/EGNOS DGPS Source  
Cold/Warm/Hot Start Time: 46/34/5 Seconds  
High signal acquisition sensitivity at -145dBm and tracking sensitivity at -150dBm  
Superior geo-location accuracy: CEP50 for 1.2 m, CEP95 for 3.0 m  
Ultra-low GPS power consumption: Full active mode at 25 mA, sleep mode at 4 uA  
Maximum speed: 515 m/s  
z
Bluetooth  
Bluetooth v 1.2 compliant, interference-tolerable with WLAN devices  
Class II, operating range up to 10 meters  
Support SPP profile  
Data rate up to 723 Kbps  
Compatible with most Bluetooth-enabled navigation devices such as cellular phones, PDAs, computers,  
etc.  
Support up to storing 8 devices pairing information  
z
General  
Better portability with internal rechargeable Lithium Polymer battery  
Low power consumption, up to 16 hours working time (in full operation mode without ITC) and 200  
hours standby time.  
Intelligent GPS Tracking and Bluetooth Connecting (ITC) manager results in extended working/standby  
time dramatically, the actual time extended will depend on how you operate the GPS Bluetooth Receiver.  
Robust performance, fast connection, accurate and sensible search of devices in range  
Stylish, portable, lightweight, mini-sized, suitable for vehicle and open-sky environment  
1.5 Package Contents  
z
z
z
z
z
GPSBT560  
1
1
1
1
1
Car Mounting Accessory  
Car Charger Set (or Traveling Charger, optional)  
External antenna (Optional)  
User Manual  
.
6
 
GPSBT560 User Manual  
1.6 Overview  
Power Key  
USB Connector  
External Antenna  
Connector  
Yellow LED  
Blue LED  
Red LED  
Figure 1 Overview  
z
z
Power Key - on/off switch  
Red LED - A battery status indicator  
In charging mode: it is always on  
In normal mode: it blinks once per minute  
In low battery mode: it gives two quick blinks every minute  
In all other modes: it is off  
z
z
Blue LED - A Bluetooth status indicator  
In pairing mode: it blinks once per second  
In connected mode: it blinks once every 4 seconds  
In all other modes: it is off  
Yellow LED - A GPS status indicator  
In GPS active mode: it blinks once every 4 seconds  
In all other modes: it is off  
z
z
External Antenna Connector (MMCX/3V)  
USB Connector - Connect to the charger  
.
7
 
GPSBT560 User Manual  
2. Using Your GPSBT560 Receiver  
GPSBT560 shall is designed mainly for outdoor applications to allow reception of GPS signals. Since the GPS  
antenna is placed under the front cover. For better signal reception, you shall always place the device facing up to  
the open sky. You shall also avoid any metal obstacles in the signal reception direction from the sky. Depending  
on the environment that you stay, the device could be used in an indoor environment such as at office or home for  
with the help of plugging an external antenna into the device. In that case, you must place the antenna outside or  
against the window and make it face up to the open sky.  
Note that, the accuracy of GPS position is affected by many facts such as poor weather conditions and satellite  
signal in general, this device should not be used for precise location measurement. You should never rely solely on  
location data from the GPS receiver. In addition, GPS can only determine your direction on the basis of your  
movement. If you stand still, GPS cannot detect which way you are facing.  
2.1 Battery Charging and Usage  
2.1.1 Battery Charging  
This receiver contains a rechargeable Li-Polymer battery. First-time charging time is about 4 hours. Later-on  
recharging time is around 2-3 hours. Detailed charging procedures as follows:  
1. Referring to Figure 2, plug the connector of the charger to the receiver’s charging port.  
2. Connect the car charger to the cigarette lighter to start charging. The Red LED will be on during charging.  
Once the battery is fully charged, the Red LED will off in power off mode, and in power on mode the Red  
LED will change to blink once per minute. You should disconnect the charger from the receiver and the  
power outlet.  
You can also use the removable USB charging cable to charge the receiver from your PC.  
Figure 2 Battery Charging  
2.1.2 Battery Information  
1. Once the battery is fully charged, the receiver supports continuous working time up to 16 hours and standby  
time about 200 hours.  
2. When the battery is low, the red LED gives two quick blinks every minute. Once the battery gets too low, the  
receiver will shutdown itself. Then all LEDs are off.  
Note that, over-charging will reduce the battery life. If a fully charged battery is left unused, it will lose power over  
time. Extreme temperature (either too hot or too cold) will also affect its ability to charge, capacity, and lifetime.  
.
8
 
GPSBT560 User Manual  
2.2 Connecting an external antenna  
The receiver provides an external antenna connector. Please refer to Figure 3 for connecting an external antenna.  
The external antenna will provide better GPS performance than the internal antenna.  
Figure 3 Connecting an External Antenna  
2.3 Placing the receiver  
There is a magic sticker in our package. The receiver can be placed at any smooth surface as indicated in Figure 4.  
Please make sure your GPS Bluetooth Receiver is facing the open sky.  
Figure 4 Mounting in the car  
Note that, some car windshields and windows may contain metal, which may block or weaken the satellite signals.  
2.4 Switching the receiver on and off  
Switching on: Push the power key up, and then the Red LED will blink once (or twice while the battery is low).  
For about 4 seconds later the Blue LED will blink once per second. This indicates the receiver is power on.  
Switching off: Push the power key down, and then all LEDs are off. This indicates the receiver is power off.  
2.5 Pairing and Connecting the GPS Receiver with Bluetooth Devices  
2.5.1 Pairing the receiver with a Bluetooth device  
Before sending GPS data to a Bluetooth device, you must pair the receiver with the Bluetooth device. Paring sets  
up a unique relationship between them and allow the receiver to memorize the unique ID (or passkey) of the device.  
This ensures that a unique and encrypted wireless link between your receiver and the device will be used.  
.
9
 
GPSBT560 User Manual  
The receiver can store up to 8 paired Bluetooth devices. Any one of them can be connected the receiver. However,  
for any give time, only one device can be connected.  
Detailed operation procedures are as follows:  
1. Place your receiver close to a Bluetooth device, and ensure that your receiver is power off, and the device is  
power on.  
2. Switch the receiver on by pushing up the power key, the Red LED blinks once per minute and the Blue LED  
blinks once per second. This indicates that the receiver has been successfully turned on and entered the paring  
mode.  
3. Following your Bluetooth device’s user guide to active Bluetooth device search, on the Bluetooth device side  
you will see a list of Bluetooth equipments found at the end of the searching process.  
4. Select this GPS Bluetooth receiver ‘GPSBT560’ from the list, and then follow the device’s instructions to  
initiate pairing operation from the device side.  
5. During the pairing process, the device will be prompted to enter a passkey. Please enter passkey “0000” to  
confirm the pairing operation between the receiver and your Bluetooth device. Once the pairing procedure is  
completed, GPS receiver will exit the pairing mode and enter the standby mode. The Blue LED will be off.  
Note  
1. The receiver will stay in the pairing mode for about 3 minutes. If no device has been paired or cannot be  
finished within 3 minutes, the receiver will exit the pairing mode and enter the standby mode. The Blue LED  
will be off and you need to go back to above steps to enter the paring process.  
2.5.2 Connecting/Disconnecting the receiver with a Bluetooth device  
Your receiver will only communicate with a paired Bluetooth device with a Bluetooth connection established in  
advance.  
Connecting your receiver with a Bluetooth device:  
Place the receiver close to the Bluetooth device, follow the device user guide to find the receiver, and then send a  
connection request to the receiver. Note that, since there can only be one Bluetooth connection at any time, the  
receiver must in the standby mode before establishing a connection to a paired device.  
Disconnecting your receiver from a Bluetooth device:  
To disconnect the receiver from a Bluetooth device, you can:  
1. Power off the receiver  
2. Refer to the device’s manual to initiate the disconnection from the device side.  
Once disconnected, the receiver will enter the standby mode and the Blue LED goes off.  
.
10  
 
GPSBT560 User Manual  
3. Important Messages and Frequently Asked Questions  
1. Red LED gives two quick blinks every minute.  
Low battery indicator; please recharge your battery as soon as possible.  
2. Can't power up the device after charging more than 20 minutes:  
For the first time, the device should be charged at least 40 minute prior tuning on, it is recommended that the  
battery should be fully charged before using the device.  
3. Receiver can not be found when a device tries to pair with it:  
Your receiver may not be in the pairing mode or within the operation range (i.e., 10 meters), please refer section  
2.5.1 for details.  
4. Do the paired receiver or the paired Bluetooth device need to be re-paired power off:  
No.  
5. Slow GPS position tracking and poor location accuracy  
The GPS signal could be very weak. You need to ensure the receiver is placed with the top side facing up to the sky.  
However, this may not necessary lead to better signal strength due to other causes such as weather conditions.  
6. Slow cold start time  
This is typically happens when you go to a new area and turn the device on or on the first-time use, of the receiver.  
In these cases, either the previous recorded geo-location data were too far away from the new location or no initial  
geo-location data can be used for cold start reference.  
.
11  
 
GPSBT560 User Manual  
4. Maintenance  
GPSBT560 is a well-designed communications device, careful maintenance and proper use will extend the product  
life. Following maintenance procedures may be helpful to you:  
z
z
Always turn off power and keep your device in a safe place when it is not in use  
Keep the device dry, away from water, precipitation, humidity, moisture, and various liquids that may corrode  
electronic circuits. If your device gets wet, turn it off immediately and wait until the device gets dry completely  
before using it  
z
z
z
z
z
z
Keep the device away from dusty and dirty places. Otherwise, the mechanic and electronic parts could be  
damaged  
Do not store the device in high temperatures or in direct sunlight. Extreme high temperature could degrade  
performance, reduce battery lifetime, and wrap or melt the certain plastics.  
Do not store the device in too cold place. Moisture could form inside the device when you take it to a warm  
place. This could damage the internal electronic circuits.  
Avoid dropping, knocking, and shaking the device. The mechanical parts and the internal electronic circuits  
could be broken.  
Avoid using hash chemicals, cleaning solvents, and any other strong detergent to clean the device. You may  
use a clean and slightly damp cloth to clean the device  
Always take to device to the nearest authorized service facility for repairing if it is malfunctioning.  
Disassembling, modifying, and replacing components yourself could degrade product performance, cause  
damages, and terminate warranty  
.
12  
 

Eagle Electronics Impact Driver EGA200 User Manual
Earthquake Sound Stereo Amplifier Cinenova 5 User Manual
Echo Trimmer 210 User Manual
Fisher Paykel Cooktop CG365D User Manual
Friedrich Clothes Dryer CP14N10 User Manual
Fujitsu Air Conditioner 9319356051 User Manual
Gemini DJ Equipment CDM 3610 User Manual
Genesis ICE Speaker Genesis 61e User Manual
Giant Water Pump GP7124A User Manual
Gigabyte Computer Hardware GA K8NE User Manual