Firstech LLC Automobile Alarm SHF 2W AS User Manual

CompuStar SHF 2W-AS  
USER’S GUIDE  
Firstech, Inc. 230 E. Potter St. Suite #8, Anchorage, AK. 99518  
1-907-563-8648  
This device complies with Part 15 of the FCC Rules.  
Operation is subject to the following two conditions:  
(1) This device may not cause harmful interference,  
and (2) this device must accept any interference  
received, including interference that may cause  
undesired operation.  
CAUTION: Changes or modifications not expressly approved by the party  
responsible for compliance could void the user’s authority to operate this device.  
Page 1 of 9  
 
 
1. OPERATION: REMOTE FUNCTIONS FOR  
AUTOMATIC TRANMISSON  
and the system will also  
Disarm/Unlock the doors as  
well.  
Button IV  
Press ½ Sec.  
Query  
Please take time to read the owners manual. If  
you have any question, please contact your  
authorized dealer.  
The LCD will show the status  
of your vehicle.  
Note: Nothing will happen if  
Also, refer to the FUNCTION printed on the back  
of your remote.  
the Button IV is pressed more than ½ Sec.  
Button I.  
Arm(Lock)/Disarm(Unlock)  
If there is no response, you are  
Press ½ Sec.  
The LCD in the remote displays 5 different  
Modes.  
out of range.  
All doors have to be closed: if  
Button I+II  
Press ½ sec.  
Mute  
not, the door in the LCD will flash.  
Mode (On/Off)  
Factory setting: No ignition locks, Active  
When the Mute Mode is Off  
Arming. The status LED will begin to flash after  
3 seconds upon locking the doors. The Starter  
Kill (Optional feature, see your dealer) will take  
into effect. The shock sensor will be in Impact  
Watch Mode for 30 seconds upon arming.  
Upon disarming, if siren chirps more than two  
times, the system has been triggered while  
armed: 3 chirping by Shock sensor, 4 chirping  
by Door sensor. Note: The system also can be  
programmed for Passive Arming. The system  
will check the doors, and if the doors are all  
closed, the system will arm itself in 30 seconds.  
If the vehicle has a dome light delay circuit and  
you have to wait until the dome lights go off  
before you Arm(Lock) the car, consult your  
authorized dealer about Passive Arming.  
when SPK is indicated in the LCD.  
Button I+III Press ½ Sec.  
Mode (On/Off)  
Valet  
Valet Mode will shut down the  
alarm and the remote starter  
system. Only the Lock/Unlock  
will work in valet mode. The  
Valet Mode can also be  
entered with the KEY. Turning  
KEY to ON from ACC three  
times within 3 seconds.  
Note: The LCD will not display  
the Zz. when the KEY is used  
to enter the Valet Mode. Press  
Button I+III to exit Valet Mode.  
Warning: Do not press Button  
I for more than ½ Sec. (See next)  
Button II+III Press ½ Sec.  
Paging mode (On/Off)  
Your remote will be paged  
Car Call/  
Button I.  
Press 2 Sec.  
To turn off Panic, press Button  
I for ½ second.  
Panic is also a Car Finder.  
Panic  
when your vehicle is being  
tampered with. The LCD will  
tell you whether it was  
tampered by Impact Sensor  
(hammer flashing) or Door  
being opened (door flashing).  
You will save the battery by  
turning Off the Paging mode.  
CAR CALL will indicate in the  
LCD when this mode is on.  
Note: The Pager will not  
respond to the first stage of the  
Shock Sensor.  
Button II.  
Start/Stop  
Press 2 sec.  
Remote  
Running time: 15 or 25 minutes  
(24/45 for diesel). Factory  
setting is 25minutes(45 for  
diesel). If there is no response,  
you are out of range.  
If the door in the LCD flashes, check to see if a  
Door is open, the Hood is open, the by-pass  
switch is On or the Brake pedal is being pressed.  
The vehicle will remain running for until,  
Programmed time elapsed, Button II pressed for  
2 seconds, Break Pedal pressed, Hood opened,  
or By-Pass Switch turned On.  
Button II+IV Press ½ Sec.  
Timer Mode (On/Off)  
24Hr.  
Your car will automatically start  
every One, Two or Three  
Hours. Factory Setting: 3 hrs.  
If you want to change the  
Factory Settings, see  
Button III  
Release (optional see dealer)  
Press 2 Sec.  
Trunk  
When the Button III is pressed  
for 2 Sec., the trunk will open  
programming section.  
Page 4 of 9  
 
Button III+IV Press ½ Sec.  
Turbo  
Warning: Do not press Button I  
for more than ½ Sec. (See next)  
Mode (2nd car on/off)  
Control Two vehicles with One  
Remote. Why is it called  
Turbo? This mode is used in  
different ways in other  
countries. Factory Setting: The  
remote control has been  
programmed to work either  
Turbo On /Off indicated in the  
LCD.  
Button I.  
Press 2 Sec.  
To turn off Panic, press Button  
I for ½ second.  
Panic is also a Car Finder.  
Panic  
Button II.  
Start/Stop  
Press 2 sec.  
Remote  
Running time: 15 or 25 minutes  
(24/45 for diesel). Factory  
setting is 25minutes(45 for  
diesel). Also, the factory setting  
is automatic Arming(Lock)  
upon completion of reservation.  
If there is no response, you are  
out of range.  
Note: If you want to program  
more than one remote to a  
vehicle, every time you  
program a remote, you must  
program the 2nd and 3rd remote  
at the same time. Up to three  
remotes to a vehicle.  
If the door in the LCD flashes without starting the  
vehicle, when the Reservation Mode has not  
been set. Also, check to see if a Door or the  
Hood is open, the by-pass switch On or the  
Parking Break released. The vehicle will remain  
running for until; Programmed time has elapsed,  
Button II pressed for 2 seconds, Parking Brake  
released, Hood opened, or by-pass Switch turned  
On.  
2. OPERATION: REMOTE FUNCTIONS FOR  
MANUAL TRANSMISSION  
Please take time to read the owners manual. If  
you have any question, please contact your  
authorized dealer.  
IMPORTANT  
Also, refer the FUNCTION printed on the back  
1. The vehicle must be in the  
NEUTRAL position.  
Button I.  
Arm(Lock)/Disarm(Unlock)  
If there is no response, you are  
out of range.  
All doors have to be closed: If  
not, the door in the LCD will flash.  
Press ½ Sec.  
2. The vehicle windows must be rolled  
up.  
3. Do not set the reservation mode  
with any people in the vehicle.  
4. Do not remote start with any people  
in the vehicle.  
Factory setting: No ignition lock, Automatic  
Arming(Lock) upon completion of reservation  
and Active Arming. The status LED will begin to  
flash after 3 seconds upon locking the doors.  
The Starter Kill (Optional feature, see your  
dealer) will take into effect. The shock sensor  
will be in Impact Watch Mode for 30 seconds  
upon Arming. Upon Disarming, if siren chirps  
more than Two times, the system has been  
triggered while armed. 3 chirping by Shock  
sensor, 4 chirping by Door sensor. If the vehicle  
has a dome light delay circuit and you have to  
wait until the dome lights go off before you  
Arm(Lock) the car, consult your authorized  
dealer.  
Note: The system is not recommended for  
vehicle with removable tops.  
Reservation Mode must be set for Manual  
Transmission vehicles to Remotely Start.  
Steps1: After arriving at the destination, and  
before turning the engine OFF, shift the  
transmission to the Neutral position.  
Step 2: Activate your parking brake.  
Step 3. Remove the key from the ignition. The  
engine will remain running.  
Step 4. Exit the vehicle and close the door  
within Two minutes from step 3. Then, the  
engine will shut Off and Reservation Mode is  
now complete.  
Note: Passive Arming. The system also can  
be programmed for Passive Arming. The  
system will check the doors. If the doors are all  
closed, the system will arm itself in 30 seconds.  
Your vehicle is now ready for remote starting.  
However, the reservation mode will be cancelled  
if Door has been opened or CompuStar has been  
put in Valet mode after Step 4, in which cases  
you have to start the vehicle with the key and  
repeat the above 4 steps if you want to restore  
the Reservation Mode.  
Page 5 of 9  
 
Note: If you try to remote start the vehicle when  
the Reservation Mode has not been set or  
cancelled, the system will not start. The  
parking light will flash Three times and the Door  
in the LCD will start flashing to inform you that  
the Reservation Mode has been cancelled or  
not been set.  
Button II+III Press ½ Sec.  
Paging mode (On/Off)  
Car Call/  
Your remote will be paged  
when your vehicle is being  
tampered with. The LCD will  
tell you whether it was  
tampered by Impact Sensor  
(hammer flashing) or Door  
being opened (door flashing).  
You will save the battery by  
turning off the Paging Mode.  
CAR CALL will indicate in the  
LCD when this Mode is On.  
Note: The Pager will not  
respond to the first stage of the  
Shock Sensor.  
Canceling Reservation Mode  
If you do not want to set the reservation mode,  
shut off the engine before you exit the vehicle.  
The engine will shut off if (a) you do not  
activate your Parking brake when you turn your  
key to Off position, (b) release your Parking  
brake while engine is running, or if (c) you  
press Button II between step 3 and 4.  
Note: The Reservation Mode will cancel if the  
Door opens or CompuStar has been put in  
Valet mode after Step 4, in which cases you  
have to start the vehicle with the key and repeat  
the above 4 steps if you want to restore the  
Reservation Mode.  
Button II+IV Press ½ Sec.  
Timer Mode (On/Off)  
24hr.  
Your car will automatically start  
every One, Two or Three  
Hours. Factory Setting: 3 Hrs.  
If you want to change the  
Factory Settings, see  
Button III  
Press 2 Sec.  
Trunk  
Release (optional see dealer)  
programming section.  
When the Button III is pressed  
for 2 Sec. The trunk will open  
and the system will also  
Disarm/Unlock the doors as  
well.  
Button III+IV Press ½ Sec.  
Mode (2nd car On/Off)  
Turbo  
Control Two vehicles with One  
Remote. Why is it called  
Turbo? This mode is used in  
different ways in other  
Button IV  
Press ½ Sec.  
Query  
The LCD will show the status  
countries. Factory Setting: The  
remote control has been  
programmed to work either  
Turbo On/Off indicated in the  
LCD.  
of your vehicle.  
Note: Nothing will happen if  
the Button IV is pressed for more than ½ Sec.  
long.  
Warning: If you want to  
program more than One  
remote to a vehicle, each time  
when you program a remote,  
you must program the 2nd and  
3rd remote at the some time.  
Up to three remotes to a  
vehicle.  
The LCD in the remote shows 5 different Modes.  
Button I+II  
Press ½ Sec.  
Mute  
Mode (On/Off)  
When the mode is Off when  
SPK is indicated in the LCD.  
Button I+III Press ½ Sec.  
Valet  
Mode (On/Off)  
Valet Mode will shut down the  
alarm and the remote starter  
system. Only the Lock/Unlock  
will work in Valet Mode. The  
Valet Mode can also be  
entered with the KEY. Turing  
KEY to ON from ACC three  
times within 3 seconds.  
3.BY-PASS SWITCH  
To shut Off the Remote Starter System, by  
putting the by-pass switch to On position. By-  
Pass switch on the Off position activates remote  
starting function.  
Note: The LCD will not display  
the Zz. when the KEY is used  
to enter the Valet Mode. Press  
Button I+III to exit Valet Mode.  
Page 6 of 9  
 
4. NEUTRRAL SAFETY SWITCH  
7. PROGRAMMING OPTIONS WITH REMOTE:  
Your vehicle should starts only in Parked or in  
Neutral position with the key. If the vehicle starts  
in any other position, the Manual Transmission  
Mode has to be activated. (Consult your  
dealer).  
Step 1: Place the key in the Ignition, and turn to  
the ON potion (vehicle not running.) (This means  
that there should be 12v at IG1 and nothing at  
the Tach sensing wire or Alternator sensing  
wire.)  
5. ALARM TRIGGER  
Step 2: Press the buttons I and IV for ½ Sec. The  
siren will chirp once, now you are in the  
Programming Mode.  
Step 3: Option 1- Ignition Lock (locks all doors  
after starting.)  
Press button I for ½ Sec. to select Option 1.Press  
button IV for ½ Sec. to not select Option 1.  
(Two chirps, confirming step 3.)  
Step 4: Option 2- locks all doors after  
reservation (Manual Transmission only).  
Please go over the procedure for Reservation  
Mode for the Manual transmission. If you choose  
Option 2, the doors will lock when you exit the  
vehicle and close the door.  
Your alarm will be triggered in the following ways:  
A. Light Impacts will trigger the 1st stage of the  
Shock Sensor, the siren will chirp 4 times and the  
parking lights will flash for a few seconds. The  
LCD will not show anything for 1st stage of the  
Shock Sensor.  
B. Heavy impacts will trigger the system with 30  
Sec. of constant siren and flashing of the parking  
lights. The Hammer in the LCD will show up and  
flash 6 times if it is in the Paging Mode.  
C. If a Door is opened, the siren will go off and  
the parking lights will flash for 30 Sec. The door  
in the LCD will flash 30 times if it is in the Paging  
Mode.  
Option 2 is recommended.  
D. Optional starter kill prevents the vehicle’s  
starter from cranking.  
Press button I for ½ Sec. to select Option 2.  
Press button IV for ½ Sec. to not select Option2.  
(Three chirps, confirming Step 3.)  
Step 5: Option 3- A. (Passive Arming) After  
the last door is closed the system will chirp every  
10 seconds and Arm itself after 3 warning chrips.  
Press Button I for ½ Sec.  
Option 3- B. (Semi-passive arming) The  
system will Arm itself after disarm like Option 3-A,  
except if a door has been opened after disarm,  
the system will not Passively arm. Press Button  
II for 2 Sec.  
Option 3- C. (Active arming) System wills  
arm/disarm only by the remote. Press Button IV  
for ½ Sec.  
6. TRANSMITTER LEARNING PROCEDURE  
Steps 1: Put the system in Valet mode with key:  
Ignition On and Off Three times with key within 3  
Sec. The parking light will flash once, when it  
enters the Valet Mode.  
Step 2: Once in the Valet Mode, within 6 Sec.  
choose one of the Lock options by pressing:  
Button I for ½ Sec. for normal locks.  
Button II for 2 Sec. for double pulse unlock  
Button III for 2 Sec. for lock pulse after Ignition  
turns Off for those vehicles that has factory  
Ignition control Door Lock and Unlocks the Door  
when the Ignition is turned Off.  
(Four chirps, confirming step 5.)  
Step 6: Option 4-A. If you enter 24Hr mode, the  
system will start the vehicle every hour. Press  
Button I for ½ Sec.  
Option 4- B. In 24Hr mode, every 2 hour. Press  
button II for 2 Sec.  
Button IV for ½ Sec. for 4-second door lock  
pulse.  
The parking light will flash twice to confirm step 2.  
Option 4- C. In 24Hr mode, every 3 hour. Press  
Button III for 2 Sec. Option 4-D. Not to program  
24Hr Mode. Press button IV for ½ sec Five  
chirps, confirming step 6.  
Step 3: Program 2nd remote or 3rd remote by  
pressing any button. The system will program up  
to 3 remotes. The parking light will flash once to  
confirm step 3.  
Note: Step 3 will remove any of the previous  
programming of the remotes. Each time when  
you program a remote, you have to program the  
2nd or 3rd remote also even if it was programmed  
previously.  
NOTE: Go through the procedures Step by Step.  
If the system dose not give the confirmation  
chirps, go through the Programming Option  
again.  
Page 7 of 9  
 
LIMIED LIFETIME WARRANTY  
Firstech, Inc. Warrants to the original purchaser that this product shall be free of defects in material and  
workmanship under normal use and circumstances for the period of time that the original owner of this  
product owns the vehicle in which it is installed; except that the remote controller unit for the period of one  
year from the date of installation to the original owner of this product. When the original purchaser returns  
the product to the retail store where it was purchased or pre-paid postal to Firstech, Inc., 230 E. Potter Suite  
8, Anchorage, Alaska 99518, USA within the warranty period, and if the product is defective Firstech, Inc,  
will at its option repair or replace such.  
“TO THE MAXIMUM EXTENT ALLOWED BY LAW, ANY AND ALL WARRANTIES ARE EXCLUDED BY  
THE MANUFACTURER AND EACH ENTITY PARTICIPATING IN THE STREAM OF COMMERCE  
THEREWITH. THIS EXCLUSION INCLUDES BUT IS NOT LIMITED TO, THE EXCLUSION OF ANY AND  
ALL WARRANTY OF MERCHANTABILITY AND/OR ANY AND ALL WARRANTY OF FITNESS FOR A  
PARTICULAR PURPOSE AND/OR AHY AND ALL WARRANTY OF NON-INFRINGEMENT OF PATENTS,  
IN THE UNITED STATES OF ANERICA AND/OF ABROAD. NEITHER THE MANUFACTURER OR ANY  
ENTITIES CONNECTED THEREWITH SHALL BE RESPONSIBLE OR LIABLE FOR ANY DAMAGES  
WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL  
DAMAGES, DAMAGES FOR LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF  
ECOMONIC OPPORTUNITY AND THE LIKE. NOTHWITHSTANDING THE ABOVE, MANUFACTURER  
DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE AS  
DESCRIBED ABOVE. Some states do not allow limitations on how long an implied warranty will last or the  
exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights,  
and you may also have other rights, which vary State to State.  
IMPORTANT NOTE:  
A product’s warranty is automatically void if its date code or serial number is defaced, missing, or altered.  
This warranty will not be valid unless you have completed the warranty card and mailed it to Firstech, Inc.,  
within 10 days after purchase to the address listed on the card.  
Page 8 of 9  
 
Registration Card  
Name__________________________________________________________  
Address________________________________________________________  
City__________________ State___________________ Zip____________  
Phone Number: Home (  
Place of Purchase__________________________ Date of Purchase______  
Purchase Model___________________ Purchase Price__________  
)_____________ Office (  
)______________  
Vehicle Make___________________ Model:_________________________  
How did you hear about this product?_______________________________  
Firstech Inc.  
230 E. Potter Suite 8  
Anchorage, AK 99518  
Page 9 of 9  
 

Echo Trimmer 999442 00120 User Manual
Electro Voice Music Mixer BK 42 Series User Manual
EVGA Computer Hardware 132 YW E179 User Manual
Exmark Lawn Mower 4500 352 User Manual
Fisher Paykel Dishwasher DD603HM User Manual
FujiFilm Digital Camera ZOOMDATE115S User Manual
Furuno Radar Detector FRS 1000A User Manual
GE Car Stereo System SCB2001K User Manual
Gemini CD Player CDJ 30 User Manual
Gemini CD Player CDX 01 User Manual