Extron electronic TV Mount LPVM 1 User Manual

Low Profile VESA Mount Kit User Guide  
Overview  
The Extron® Low Profile VESA® Mount Kit (LPVM-1) allows  
monitors or Extron touch panels to be wall mounted to a two-gang  
UL-certified junction box, a two-gang mud ring, or directly onto  
any solid surface, such as brick, wood, masonry, or drywall. The kit  
supports both the B-type (20 x 50 mm) and D-type (75 x 75 mm)  
VESA mounting patterns. The monitor attaches to the wall at a fixed  
angle with no tilting.  
Tongue  
Holes to Secure  
Plate 1 to Wall  
Bottom Tabs (2)  
Holes to Secure  
Plate 1 to Mud Ring  
or Junction Box  
CAUTION: The maximum loads for the LPVM-1 are:  
VESA B 4.4 pounds (2 kg)  
VESA D 30.8 pounds (14 kg) if the LPVM-1 is  
mounted directly to the wall, not a mud ring.  
Extron LPVM-1  
Plate 1  
The kit consists of two separate steel plates, held together by two  
locking screws. Plate 1, which attaches to the wall, has a protruding  
tongue at the top. The tongue fits into a groove at the top of plate  
2, which attaches to the back of the display device (see the figure at  
right).  
Groove  
B-Type VESA  
Mount Holes  
D-Type VESA  
Mount Holes  
Optional Tools and Equipment  
Locking Screws  
(#10-32 Phillips)  
To mount the LPVM-1, you may need some or all of the following  
items that are not provided by Extron:  
Bottom Edge  
Mud ring or UL-certified junction box  
Tools for cutting a hole in drywall  
Conduit or surface raceway  
Extron LPVM-1  
Plate 2  
Power drill with a bit that is appropriate for the wall type  
Screwdriver  
Four screws or bolts, to attach the LPVM-1 to the wall (these must be appropriate for the type of wall).  
Installation Instructions  
To VESA mount a touch panel or monitor using the LPVM-1, follow these instructions:  
3
Disassembling the LPVM-1  
1. Use a Phillips screwdriver to loosen the two locking screws until the two plates of the  
LPVM-1 can separate.  
2. Swing the bottom tabs of plate 1 away from the bottom edge of plate 2.  
3. Pull plate 1 down to remove the tongue from the groove in plate 2.  
1
4. Select a suitable mounting site and decide whether the LPVM-1 will be mounted directly  
to the wall (see below), or to a mud ring or UL-certified junction box (see the next page).  
2
Mounting the LPVM-1 Directly to a Wall:  
a. If the LPVM-1 is being mounted directly to drywall, you may cut a  
hole in the drywall that is 2.5 x 2.5 inches (6.35 x 6.35 cm) to run  
cables inside the wall cavity. If the LPVM-1 is attached to a solid wall  
or you do not want to run cables through the drywall cavity, the  
cables should be enclosed in conduit or raceway.  
4b  
4c  
b. Use plate 1 to mark the position of the four holes in the wall and  
drill four holes, using a drill bit that is appropriate for the wall type.  
Plate 1 accommodates screws up to 1/4 inch in diameter.  
Screws (4)  
Appropriate  
to Wall Type  
c. Secure plate 1 to the wall with four screws or bolts that are  
appropriate for the wall type. Ensure the tongue is facing up.  
 

Elation Professional Work Light 60TM User Manual
Excalibur electronic Motorized Toy Car PR11BK 2 User Manual
FEIN Power Tools Drill ASKEU 636 Kin User Manual
Fisher VCR FVH T619 User Manual
FujiFilm Camera Lens 2030526 User Manual
GE Air Conditioner AEV24DK User Manual
GE Microwave Oven JE1160 User Manual
GE Oven PT916BM User Manual
GE Ventilation Hood JN322 User Manual
GN Netcom Headphones STRATUS ULTRA G User Manual