Extron electronic Switch XPA 2002 100V User Manual

Product Category  
XTRA™ Full Rack Series • Setup Guide  
This guide provides basic instructions for an experienced installer to set up and operate the Extron XTRA Full Rack Series of  
power amplifiers. All user guide references refer to the XTRA Full Rack Series User Guide.  
XPA 2002 outputs stereo audio at 200 watts rms per channel (4-ohm speakers) or 100 watts rms per channel (8-ohm  
speakers) on channels 1 and 2. Output is 400 watts bridged mono (8-ohm speaker).  
XPA 2002-70V outputs 200 watts rms per channel on channels 1 and 2 for 70 V systems.  
XPA 2002-100V outputs 200 watts rms per channel on channels 1 and 2 for 100 V systems.  
XPA 2003C-70V outputs 200 watts per channel (4-ohm speakers) or 100 watts per channel (8-ohm speakers) on channels  
1 and 2, and 200 watts (70 V line, mono) on channel 3.  
XPA 2003C-100V outputs 200 watts per channel (4-ohm speakers) or 100 watts per channel (8-ohm speakers) on  
channels 1 and 2, and 200 watts (100 V line, mono) on channel 3.  
XPA 2004 outputs stereo audio at 200 watts per channel (4-ohm speakers) or 100 watts per channel (8-ohm speakers) on  
channels 1, 2, 3, and 4. Output is 400 watts per bridge in bridged mono (8-ohm speakers) on bridge A (channels 1 and  
2) and bridge B (channels 3 and 4).  
XPA 4002 outputs stereo audio at 400 watts rms per channel (4-ohm speakers) or 200 watts rms per channel (8-ohm  
speakers) on channels 1 and 2. Output is 800 watts bridged mono (8-ohm speaker).  
XPA 4002-70V outputs 400 watts rms per channel on channels 1 and 2 for 70 V systems.  
Installation  
1. Power off — Turn off all equipment including the XPA amplifier by toggling the power off and disconnecting the  
power cord. Verify that the amplifier is disconnected from the power source before proceeding.  
2. Mount the amplifier — For diagrams of typical application examples, see the “Application Examples” section in the user  
guide. For further mounting instructions, see the “Mounting the XTRA Series of Power Amplifiers” section in the user  
guide.  
3. Wire the input — Wire the input to the 3.5 mm input connectors of the amplifier, as shown in the following illustration.  
See the “Rear Panel Features and Operation” section in the user guide for bridging information.  
NOTE: Control signal ground pins may be labeled as or “G”. Audio ground pins may be labeled as or .  
The wiring and function are the same, whichever way your product is labeled.  
1
2
" (5 mm) MAX.  
Tip  
Ring  
Sleeve  
Tip  
Sleeve  
(BRIDGE)  
Balanced Input  
Unbalanced Input  
NOTE: The wires must not be tinned: tinned wire does not hold tight in the captive screws and can break easily  
after several bends.  
4. Wire the outputs Wire speakers to the output connectors of the amplifier using the included 2-pole (70 V or 100 V)  
or 4-pole (8 ohm or 4 ohm) screw lock plug.  
2-pole (70 V or 100 V) output connector wiring:  
4-pole (8 ohm or 4 ohm) output connector wiring:  
1
1
2
2
OUTPUT  
1
Do not tin the wires!  
Do not tin the wires!  
OUTPUT  
70V  
CAUTION: Do not short the “+” and “ ” outputs to each other. Doing so may damage the amplifier.  
For complete wiring details, see “Rear Panel Features and Operation” in the user guide.  
1
 

Eagle Electronics Fish Finder 640C User Manual
Edimax Technology Switch ES 3105P User Manual
Extron electronic Stereo Amplifier FOX 500 DA6 User Manual
Fellowes Laminator CL 95 CL 125 User Manual
Fisher Price Motorized Toy Car H3427 User Manual
Ford Automobile 2011 Fusion Hybrid User Manual
Frymaster Fryer Protector Series User Manual
Gardena Water Pump T 380 User Manual
Garland Convection Oven SUMG 100 GAS User Manual
GE Double Oven JB850 User Manual