GE Monogram Refrigerator ZIR36NDGE User Manual

Monogram.  
ZIR36ND–GE Monogram 36" Built-In All-Refrigerator  
Product Dimensions (in inches)  
Design Information  
10-3/4" Max.  
10" Min.  
24-3/4"  
35" Case  
Designed to be installed flush or semi-flush with surrounding cabinetry. Cutout  
dimensions, clearances and side panel sizes are determined by the many  
installation options available. Side panels must be used whenever the sides of  
the refrigerator will be exposed. Side panels are not required when installed  
into an enclosure or between pantry and oven cabinets. IMPORTANT - Side  
panels, 1/2" minimum thickness are required when using FRAMELESS  
CABINETS.  
36" Overall  
Field installed custom panels, Lexan® or stainless steel panels are required.  
The door and grille panel sizes vary to accommodate the kit being used.  
The supplied toekick is vented and must remain unobstructed for proper  
air circulation.  
26-3/4"  
84-1/2" Max.  
83-1/2" Min.  
73-1/2"  
Optional Panel Kits:  
ZWBR36: Black Lexan® Panel Kit  
ZWWR36: White Lexan® Panel Kit  
ZWSR36: Stainless Steel Panel Kit  
Optional Custom Trim Kits:  
ZKHR1: For installation of a custom handle of your choice onto a 1/4" Panel.  
ZKTR36LH or ZKTR36RH: For installation of a 3/4" thick custom panel.  
ZKHTR1: For installation of a custom handle of your choice onto a 3/4" thick  
panel. (This kit must be used in combination with ZKTR36LH or ZKTR36RH).  
ZKHRSS1: Tubular Stainless Steel handle for 1/4" thick panel.  
ZKHTRSS1: Tubular Stainless Steel handle for 3/4" thick panel.  
ZGC2: 1/4" grille panel frame side pieces for 83-1/2" and 84-1/2" installation  
heights. (Factory set for 84").  
4"  
*Finished Width  
ZWT1: White toekick (supplied toekick is black).  
Electrical  
Area  
Wall View  
ZFC1: Trim strip for side-by-side installation of  
two products.  
7 1/2"  
7"  
Additional Specifications  
A 115 volt 60Hz., 15 or 20 amp power supply is required. An individual  
properly grounded branch circuit or circuit breaker is recommended. Install a  
properly grounded 3-prong electrical receptacle recessed into the back wall.  
Electrical must be located on rear wall as shown.  
Water line can enter opening through the floor or back wall. The water line  
should be 1/4" O.D. copper tubing between the cold water line and water  
connection location, long enough to extend to the front of the refrigerator.  
Installation of an easily accessible shut off valve is recommended.  
5"  
24 3/4" Total  
Depth  
84 1/2" max  
83 1/2" min  
Finished  
74" From Floor  
to Bottom  
of Electrical  
Opening  
5"  
5" Water Supply  
3 1/2"  
3 1/2"  
Clearances:  
If the refrigerator or freezer is installed in a corner:  
A 4" clearance is required on the hinge side for a 90° door opening and  
access to fresh food drawers. A 10" clearance is required on the hinge side to  
remove pans.  
* 36" Min. for a flush installation into an enclosure.  
* 35-1/2" Min. for a semi-flush installation into an enclosure.  
Note: Additional cutout width may be required when side panels  
are used. Add side panel thickness to the finished cutout width to  
calculate rough-in width.  
®
For answers to your Monogram,  
GE Profile Performance Series,™  
GE Profileor GE appliance questions, call  
GE Answer Center® service, 800.626.2000.  
Listed by  
Underwriters  
Laboratories  
R
Specification Created 8/00  
 
Monogram.  
ZIR36NDGE Monogram 36" Built-In All-Refrigerator  
Side By Side Installation of Freezer and Refrigerator  
*Finished Width  
Electrical  
7"  
Wall View  
7 1/2"  
23 1/2"  
84"  
7"  
5"  
5"  
24 3/4" Total  
Depth  
84 1/2" max  
83 1/2" min  
Finished  
74" From Floor  
to Bottom  
of Electrical  
Opening  
36"  
5"  
Water Supply  
24-3/4"  
36"  
26"  
Freezer  
For a complete food storage center, install a Monogram  
Freezer and Refrigerator side by side. For even more  
capacity, install two refrigerators and one or two  
freezers. Order ZFC1 Trim Kit to cover the side trim  
and/or gap between the two products.  
3 1/2"  
Refrigerator  
*72" min. for a flush installation  
71-1/2" min. for a semi-flush installation  
Note: Additional cutout width may be required when side  
panels are used. Add side panel thickness to the finished  
cutout to calculate rough-in width.  
• The electrical and water locations must be located as  
shown for either type of installation. A separate 115V,  
60Hz. 20 amp power supply is recommended for each  
product.  
Installation Between Base and Wall Cabinet  
1/4" Thick  
Side Panels  
Refrigerator  
Cabinet  
Finished Dim.  
Rough-In Dim.  
35-1/2"  
36"  
Refrigerator door  
Cabinet  
Refrigerator or Freezer  
Note: 1/4" thick side panels  
can be inserted into the case  
trim, making the rough-in the  
1/4" Thick  
Side Panels  
same as the outside trim  
width, 36.  
Finished Dim.  
Rough-In Dim.  
71-1/2"  
72"  
®
For answers to your Monogram,  
GE Profile Performance Series,™  
GE Profileor GE appliance questions, call  
GE Answer Center® service, 800.626.2000.  
Refrigerator and Freezer  
installed side-by-side  
ZFC1 Trim Kit is recommended to cover side trim  
and/or gap between the two products.  
Listed by  
Underwriters  
Laboratories  
R
Specification Created 8/00  
 
Monogram.  
ZIR36NDGE Monogram 36" Built-In All-Refrigerator  
Installation at End of Run  
Refrigerator  
Cabinet  
Refrigerator door  
Cabinet  
Note: 1/2" thick side panels shown. Side  
panels can be any thickness. Add side panel  
thickness to outside trim width, (36or 72" for  
two models) to calculate the rough-in  
dimension. The leading (front) edge must be  
finished to match surrounding cabinetry.  
Refrigerator and Freezer  
Refrigerator or Freezer  
installed side-by-side  
1/2" Thick  
1/2" Thick  
Side Panels  
Side Panels  
Finished Dim.  
72"  
36"  
37"  
Finished Dim.  
Rough-In Dim.  
73"  
Roughed-In Dim.  
Frameless Cabinets  
Side panels, 1/2" minimum thickness are required when using frameless cabinets. The side  
panel acts as a spacer between the cabinet and the case trim and prevents interference  
with cabinet door swing. The leading (front) edge must be finished to match surrounding  
cabinetry.  
Refrigerator  
Cabinet  
1/2" To 3/4" Side Panels. Leading  
Edge Flush With Cabinet  
Refrigerator door  
Accessory Panel Kits  
A wide range of custom appearance options can be created with  
optional trim kits.  
These refrigerators and freezers require field installed door and  
grille panels.The factory installed trim will accept accessory panel  
kits. White or black Lexan® and stainless steel kits are available.  
Panels are cut to size and ready to install. These panel kits must be  
ordered separately.  
ZWBR36, Black Lexan® Panels  
ZWWR36, White Lexan® Panels  
ZWSR36, Stainless Steel Panels  
Accessory Panel Kits Advanced Planning Exterior Appearance Options  
These refrigerators and freezers are designed to be customized  
with decorator door and grille panels. Field installed custom door  
and grille panels are required for these models.  
You should:  
1. Select the appearance option.  
2. Order the trim kit for that option.  
3. Order the custom door and grille panels from the cabinet  
manufacturer. The exact dimension for each trim kit application is  
provided in this booklet. Find and pull out the page for your  
application and fax or send it to the cabinet manufacturer. The  
cabinet manufacturer must have this information to construct the  
panels accurately.  
Factory installed trim will accommodate 1/4" thick custom panels,  
Lexan® or stainless steel panel kits.  
Door and grille panel sizes vary to accommodate the kit being used.  
Sizes are provided in this booklet.  
4. Determine the final installation situation and order matching  
side panels.  
Caution: Maximum door panel weight is 50 pounds.  
®
For answers to your Monogram,  
Side panels must be used whenever the sides of the refrigerator will  
be exposed. Side panel sizes vary depending on the installation.  
GE Profile Performance Series,™  
GE Profileor GE appliance questions, call  
GE Answer Center® service, 800.626.2000.  
3/4" thick custom panels-Without trim kits  
A raised panel design, screwed or glued to a 1/4" thick backing can  
be used.  
Listed by  
Underwriters  
Laboratories  
Specification Created 8/00  
R
 
Monogram.  
ZIR36NDGE Monogram 36" Built-In All-Refrigerator  
Custom Door Panel Dimensions Using Standard Trim  
1/4" thick panels or  
ZIR36N Refrigerator  
ZIF36N Freezer  
Panels secured to 1/4" thick backing  
1/4" Panel: Cut panels to size.  
Custom handle with 1/4" door panel requires Trim kits ZKHR1 or ZKHRSS1  
for tubular stainless steel handles.  
35-1/16"  
Standard Trim with Panels secured to 1/4" thick backing  
Applying a raised panel design to a 1/4" thick backing (screws or glued):  
Cut 1/4" thick panels to size. Fabricate the raised panel to permit at least  
2" fingertip clearance of the standard handle. 1-1/4" clearance from the  
hinge side to avoid striking adjacent cabinetry and 5/16" from the top and  
bottom edges to allow for the trim flange.  
1/4" Thick  
Custom Panel  
Note: ZKHTR1 custom handle kit cannot be used in this configuration.  
Custom Grille Panel  
35 1/8"  
68-7/8"  
8"  
1/4" Thick Panel  
The grille panel frame is factory assembled for 84"  
installation height. If installation height varies, order  
ZGC2 trim kit that provides optional side trim pieces. Cut  
grille panel to sizes shown below.  
Important: Maximum panel is 50 pounds  
Installation Height Panel Height  
83-1/2"  
84-1/2"  
7-1/2"  
8-1/2"  
Raised Panel on 1/4" Thick Backing  
Using Standard Handles  
5/16" Clearance  
1/4"  
Thick  
Backing  
Appearance  
Panel  
2" Clearance  
handle Side  
Raised Panel  
on 1/4" Thick  
Backing With  
Standard  
1-1/4"  
Clearance  
hinge side  
Handles  
®
For answers to your Monogram,  
GE Profile Performance Series,™  
GE Profileor GE appliance questions, call  
GE Answer Center® service, 800.626.2000.  
5/16" Clearance  
5/16" Clearance  
Listed by  
Underwriters  
Laboratories  
R
Specification Created 8/00  
 
Monogram.  
ZIR36NDGE Monogram 36" Built-In All-Refrigerator  
Custom Door Panel Dimensions  
Using Trim Kits ZKTR36LH or ZKTR36RH  
3/4" thick panel with kit supplied handle  
ZIR36N Refrigerator  
ZIF36N Freezer  
The ZKTR36LH (or ZKTR36RH) trim kit provides for the installation of 3/4" thick  
custom door and grille panels, using the supplied handle. Cut panel to size  
and install.  
35 -1/16"  
Important: Maximum panel is 50 pounds  
3/4" Thick  
Custom Panel  
68-15/16"  
Custom Grille Panel  
35 1/4"  
A
3/4" Thick Panel  
Grille Panel height can vary to fill installation height.  
Installation Height Dimension A  
83-1/2"  
84"  
84-1/2”  
7-1/2"  
8-1/2"  
8-3/4”  
Important: Maintain 1-1/2min. gap between top  
of door and bottom of grille panel.  
®
For answers to your Monogram,  
GE Profile Performance Series,™  
GE Profileor GE appliance questions, call  
GE Answer Center® service, 800.626.2000.  
Listed by  
Underwriters  
Laboratories  
R
Specification Created 8/00  
 
Monogram.  
ZIR36NDGE Monogram 36" Built-In All-Refrigerator  
Custom Door Panel Dimensions Using Standard Trim  
Using Trim Kit ZKTR36LH or ZKTR36RH  
3/4" thick panel with custom handle  
ZIR36N Refrigerator  
ZIF36N Freezer  
The ZKTR36LH (or ZKTR36RH) trim kit installed together with a ZKHTR1 custom  
handle kit provides for the installation of 3/4" thick custom door and grille  
panels with a custom handle of your choice. Order ZKHTRSS1 for a tubular  
stainless steel handle. Cut panels to size, rout the handle side of the panel as  
shown below and install.  
35 1/4 "  
3/4" Thick  
Custom Panel  
With Custom  
Handle  
Important: Maximum panel is 50 pounds  
68-15/16  
Custom Grille Panel  
35 1/4"  
A
3/4" Thick Panel  
Grille Panel height can vary to fill installation height.  
Rout back side of panel as shown  
on the handle side  
1-13/16"  
1/4"  
max  
Appearance Side  
Installation Height Dimension A  
83-1/2"  
84"  
84-1/2”  
7-1/2"  
8-1/2"  
8-3/4”  
Important: Maintain 1-1/2" min. gap between top of door  
and bottom of grille panel.  
®
For answers to your Monogram,  
GE Profile Performance Series,™  
GE Profileor GE appliance questions, call  
GE Answer Center® service, 800.626.2000.  
Specification Created 8/00  
Listed by  
Underwriters  
Laboratories  
R
 
Monogram.  
ZIR36NDGE Monogram 36" Built-In All-Refrigerator  
Side Panel or Filler Options (Not to scale)  
Side panels must be used whenever the sides of  
the refrigerator or freezer will be exposed.  
1/2" to 3/4" Side  
Panels Leading Edge  
Flush with Cabinet  
23 9/16"  
24 3/4"  
Front. The front or  
leading edge must be  
finished to match  
cabinetry.  
1/4" Side Panels  
Insert end of  
side panel into trim.  
Top View  
Top View  
84"  
84"  
Trim  
2 9/16"  
3 3/4"  
Standard 4" high toekick or trim to fit.  
Height may vary depending on application.  
Standard 4" high toekick or trim to fit.  
Height may vary depending on application.  
23 5/16"  
1/2" to 3/4" Side  
Panels Recessed  
front edge.  
Top View  
84"  
®
For answers to your Monogram,  
2 5/16"  
GE Profile Performance Series,™  
GE Profileor GE appliance questions, call  
GE Answer Center® service, 800.626.2000.  
Standard 4" high toekick or trim to fit.  
Height may vary depending on application.  
Listed by  
Underwriters  
Laboratories  
R
Specification Created 8/00  
 
Monogram.  
ZIR36NDGE Monogram 36" Built-In All-Refrigerator  
Features and Benefits  
21.9 Cu. Ft. Fresh Food Capacity  
Spill Proof Glass Shelves (6 Adjustable,  
1 Full-Width Fixed)  
Sealed Snack Pans with  
Full-Extension Slides  
2 Extra Large Adjustable Humidity Produce  
Pans with Easy Access Lid and Full  
Extension Slides  
Wine Caddy  
4 Large Wire Baskets with  
Full-Extension Slides  
4 Door Bins with Gallon Storage  
2 Sealed Dairy Compartments with Glass  
Covered Butter Dish  
Egg Bin  
Auto Cycle Defrost Sealed System Design  
Full Extension Accuride Slides  
Custom Panels Required  
Model ZIR36NDRH - Right hand  
door opening  
Model ZIR36NDLH - Left hand  
door opening  
Available Fall 2000  
Specification Created 8/00  
 

Clarion CD Player iDXZ775USB User Manual
Conair Indoor Furnishings 06PM8032 User Manual
Craftsman Pressure Washer MGP 769010 User Manual
Dualit Kitchen Grill Sandwich Cage User Manual
Dynex Flat Panel Television DX 32L151A11 User Manual
Dynex Flat Panel Television DX 40L260A12 User Manual
Edifier Enterprises Canada Speaker System R401 User Manual
Electro Voice Microphone 635N D B User Manual
Extron electronic Stereo Amplifier P 2 DA8 A User Manual
GE Toaster 681131690461 User Manual