Extron electronic Switch DFX 100 User Manual

DFX 100 Series • Setup Guide  
The Extron DFX 100 Series consists of a transmitter (DFX 100 Tx) and receiver (DFX 100 Rx)  
that use one multimode fiber optic cable to extend a DVI-D signal up to 984 feet (300 m).  
This guide provides basic instructions for an experienced installer to set up and operate the  
DFX 100 (for full instructions see the DFX 100 Series User Guide, at www.extron.com).  
Installation  
Step 1 — Mounting  
Mount the DFX 100 Tx close to the DVI source and the DFX 100 Rx close to the DVI display  
device. See the DFX 100 Series User Guide for all mounting options. Follow the instructions  
provided with the appropriate installation kit.  
Step 2 — Cable Connections  
DFX 100 Series Front Panel  
DFX 100 Tx Rear Panel  
DFX 100 Rx Rear Panel  
POWER  
POWER  
DFX 100 Tx  
DFX 100 Rx  
12V  
12V  
-
-
A
MAX  
-
-
A
MAX  
b
d
b
f
a
OUTPUT  
INPUT  
Extron  
c
INPUT  
OUTPUT  
e
1. Connect one of the provided 12 VDC power supplies to the rear panel captive screw  
connectors of the transimtter and the other to the receiver ( ).  
b
ATTENTION: Before connecting power to the DFX 100 Tx or Rx, see the attention  
box in the “Power Supply” section of the DFX 100 Series User Guide for important  
information about power supplies.  
NOTES:  
When the units receive power but no input signals, the front panel LED ( ) lights  
amber.  
When the transmitter receives power and a DVI input signal, the front panel LED lights  
green  
When the receiver receives power and a fiber optic input signal, the front panel LED  
lights green.  
a
2. Connect the DFX 100 Tx output ( ) to the DFX 100 Rx input ( ) using one multimode  
d
f
cable (not provided).  
WARNING: Possible Damage to Eyesight. The DFX 100 outputs continuous  
invisible light (Class 1 rated), which may be harmful and dangerous to the eyes; use  
with caution. Do not look into the rear panel fiber optic cable connector or into the  
fiber optic cable itself. Plug the attached dust cap into the optical transceiver when  
the fiber optic cable is unplugged.  
3. Connect the DVI display to the DVI output connector of the DFX 100 Rx ( ). Power on the  
e
display.  
 
DFX 100 Series • Setup Guide (Continued)  
4. Connect the DVI source to the DVI input connector of the DFX 100 Tx ( ). Power on the  
c
source.  
NOTE: Although the transmitter and receiver have DVI-I connectors, both devices are  
compatible only with a single link DVI-D signal.  
Application Diagram  
Extron  
DFX 100 Tx  
Transmitter  
DFX 100 Tx  
R
E
W
O
P
12V  
X
-
A
MA  
OUTPUT  
T
INPU  
Fiber  
Up to 300m ( 984 ft )  
on Multimode Fiber  
DVI  
Extron  
DFX 100 Rx  
Receiver  
PC  
DFX 100 Rx  
R
POWE  
12  
X
V
-
-
A
MA  
T
INPU  
OUTPUT  
DVI  
Flat Panel Display  
Extron Headquarters  
+800.633.9876 Inside USA/Canada Only  
Extron Europe  
+800.3987.6673  
Inside Europe Only  
Extron Asia  
+800.7339.8766  
Inside Asia Only  
Extron Japan  
+81.3.3511.7655  
FAX:  
Extron China  
+4000.EXTRON  
+4000.398766  
Inside China Only  
+86.21.3760.1568  
FAX:  
Extron India  
1800.3070.3777  
Inside India Only  
+91.80.3055.3777  
FAX:  
+91.80.3055.3737  
Extron Korea  
Extron USA - West  
+1.714.491.1500  
Extron USA - East  
+1.919.850.1000  
+81.3.3511.7656  
+31.33.453.4040  
+65.6383.4400  
Extron Middle East  
+971.4.299.1800  
FAX:  
FAX:  
+1.714.491.1517  
FAX:  
+31.33.453.4050  
FAX:  
+65.6383.4664  
+86.21.3760.1566  
+1.919.850.1001  
+82.2.3444.1571  
FAX: +82.2.3444.1575  
+971.4.299.1880  
© 2013 Extron Electronics All rights reserved. www.extron.com  
68-2149-50 Rev A 04 13  
 

Clover Electronics Digital Camera RD435 User Manual
Craftsman Blower 358799430 User Manual
Crate Amplifiers Musical Instrument Amplifier G60 User Manual
Cub Cadet Snow Blower SWE 528 User Manual
Dacor Oven DO130 User Manual
Dimplex Fan DCU18LCD User Manual
Dynacord Stereo Amplifier PowerH Series User Manual
Estate Refrigerator 2315225 User Manual
EVGA Computer Drive 100 U2 UV19 User Manual
Frigidaire Clothes Dryer FDEB34RG User Manual