Electro Voice Speaker System HP64 User Manual

HP64  
TransPlanar™  
Constant-Directivity  
Horn  
General Product Description  
The Electro-Voice® model HP64 is a wide-range,  
flat-front, high-frequency, constant-directivity horn. The  
horizontal angle is controlled over a frequency range  
of 1.7 kHz to 20 kHz and the vertical angle is controlled  
from 1.8 kHz to 20 kHz, both with unusual precision  
and adherence to the intended angle. Furthermore,  
excellent loading is maintained to a low frequency of  
1000 Hz.  
The flat-front design makes the HP64 suitable for all  
modern boxed and clustered systems. A special vaned  
waveguide throat detail gives the HP64 unusually good  
high-frequency control, vertically, when compared to  
similar 2-inch-throat horn designs.  
Architects’ and Engineers’ Specifications  
shall be integrally laminated into the fiberglass portion  
of the horn.  
The horn shall be of the constant-directivity type.It shall  
produce a horizontal beamwidth (6 dB-down angle) of  
60 degrees, deviating no more that 30 degrees from  
this angle over the frequency range 2,000 to 20,000  
Hz. It shall produce a vertical beamwidth of 40 degrees,  
deviating no more than 20 degrees from this angle over  
the frequency range 1,600 to 20,000 Hz. In addition, it  
shall provide useful acoustic loading at all frequencies  
above 1000 Hz.  
The horn shall possess a throat of 4.92-cm (1.94in.)  
diameter and its flange shall be provided with four ¼-  
20 clearance bolt holes on a 10.2 cm (4.0 in.) circle for  
the mounting of the compression driver. The horn shall  
be 27.9 cm (11.0 in.) high, 22.2 cm (8.8 in.) wide, and  
22.2 cm (8.7 in.) long. It shall weigh no more than 2.5  
kg (4.5 lb).  
The horn shall be of hybrid fiberglass-and-zinc  
construction. The driver-mounting flange and initial  
throat section shall be constructed of die-cast zinc and  
The horn shall be the Electro-Voice model HP64  
constant-directivity horn.  
Specifications:  
Construction:  
The following specifications are in accordance with or  
exceed the AES Recommended Practice for  
Specification of Loudspeaker Components Used in  
Professional Audio and Sound Reinforcement  
(AES2-1984; ANSI S4.26-1984).  
Polyester resin and glass-fiber laminate integrally  
molded to a die-cast zinc throat section. This hybrid  
construction assures a rigid driver mount, accurate,  
loss-free throat-wave transmission and low total weight  
compared to horns of similar size.  
Horizontal Beamwidth:  
Mechanical Connection of Driver:  
60° (+30°, -10°) (-6 dB 1.7 kHz to 20 kHz)  
Vertical Beamwidth:  
Bolt on; standard 2" diameter throat, 5" diameter  
mounting flange and four clearance holes for 1/4" bolts  
on a 4" diameter bolt circle. (See Figure 1).  
40° (+20°, -10°) (-6 dB, 1.8 kHz to 20 kHz)  
Directivity Factor Rθ (Q):  
Recommended Driver:  
DH1A, DH2A  
Weight:  
18.1 (average 1.6 kHz to 20 kHz)  
Directivity Index Di:  
12.6 dB (+0.9, -2.9 dB)  
10 log Rθ, (average 1.6 kHz to 20 kHz)  
2.5 kg (4.5 lb)  
Lowest Recommended Crossover Frequency:  
1000 Hz  
 

Clover Electronics Flat Panel Television LCD2084 User Manual
Contec Computer Hardware SPI 8450 LLVA User Manual
Cooper Lighting Indoor Furnishings 12V MR16 User Manual
Cub Cadet Lawn Mower GT 3200 User Manual
Cuisinart Blender CH 4 User Manual
Cuisinart Water System PG 24576 User Manual
Curtis Flat Panel Television LCDVD2224A User Manual
Dualit Electric Grill RSG1 User Manual
Faber Ventilation Hood Wall Mount Canopy Rangehood User Manual
Flymo Lawn Mower lawnrake User Manual