Dymo Printer INRatio Printer User Manual

INRatio Printer QUICK REFERENCE GUIDE  
Meter Display  
Setting Up the Printer  
1. Plug the printer cable into the dataport jack in the meter.  
Plug the other end of the cable (pins) into the printer.  
NOTE: Your cable will look different than the one shown  
in the Axiohm User Manual.  
Connecting the Printer  
to the INRatio Meter  
Plug the power supply into the printer then a wall jack.  
2. Press any button to turn on the meter.  
The meter will begin a self test.  
3. The meter will prompt for a new test strip.  
Back of  
Meter  
Back of Wall  
Printer Jack  
4. Press the MENU button to view the Main Menu.  
Loading a Roll of Labels  
1. Open the Printer Cover.  
2. Remove the Spindle.  
5. Press the UP/DOWN button to highlight “CHANGE SETUP”.  
Press the OK button to select.  
6. Press the UP/DOWN button to highlight “PRINTER”.  
Press the OK button to select.  
7. The PRINTER options will be displayed.  
Press the UP/DOWN button to choose PRINTER.  
Press the OK button to select.  
3. Load Labels on Spindle.  
4. Cut the lead label to create  
a nice straight edge.  
8. Press the MENU button to return to the Change Setup Menu.  
9. Press the MENU button to return to the Main Menu.  
10. If you wish to perform a test at this time, highlight “RUN TEST”  
in the menu by pressing the UP/DOWN button.  
Press the OK button to select.  
5. Be sure the power cord is  
connected and the printer is  
on. The green power light will  
flash and you will hear the  
printer motor turning.  
Printing Current Test Result  
6. Feed the first label into the  
feed slot on the inside of the  
printer. The motor will grab  
the first label and draw the  
labels through the front slot,  
stopping automatically after  
the first label.  
1. Make sure the printer is set up properly by following the  
directions above. After performing a test, the meter will beep  
and the test results will appear on the display. Press OK, and  
the meter will ask if you would like to print. Press OK to print.  
Printing Previous Test Results From Memory  
1. Press the MENU button to view the Main Menu.  
2. Press the UP/DOWN button to highlight "PRINT MEMORY".  
Press the OK button to select.  
Shoulder  
slots  
Cover  
3. Press the UP/DOWN button to select one of the following,  
then press OK to select:  
PRINT LAST:  
PRINT LAST 7:  
Prints most recent test result  
Prints last 7 test results  
Power  
Light  
On/Off Form  
Button Feed  
PRINT LAST 15: Prints last 15 test results  
PRINT ALL: Prints all test results in memory  
7. If the motor stops while  
loading, press the Form Feed  
button to advance the label.  
Troubleshooting & Error Messages  
Recommended Labels:  
Dymo White Shipping Labels  
2-1/8"x4", 220 labels per roll  
Dymo part #30323 or #30573  
Available at office supply stores  
2-1/4"x4" or 2-5/16"x4"  
If the printer is unattached and "PRINT MEMORY" is chosen the  
meter will display "ERROR PRINTER PROBLEM". Make sure the  
printer is on, and all cables are connected properly.  
8. Make sure the Spindle is  
settled into the shoulder slots.  
9. Close the Printer Cover  
When the printer is out of labels the meter will display "ERROR  
PRINTER OUT OF PAPER". Load a new roll of labels into the printer.  
will also work.  
P/N 0200184 Rev-A  
 

Clarion CD Player BD159R
Clarion CD Player DXZ615 User Manual
Crate Amplifiers Stereo Amplifier 6210 User Manual
Cuisinart Bread Maker CBK 200 User Manual
Delta Electronics Network Card VFD F Series User Manual
Extron electronic Stereo Receiver MTP 15HD User Manual
Extron electronic Switch AAP 314 User Manual
Fender Musical Instrument Amplifier G DEC 30 User Manual
FUNAI VCR 31B 254 User Manual
Gefen Switch EXT TV MFS User Manual