Register your MBR900
Mobile Broadband N Router Today!
MBR900
Mobile
Broadband
~ YOU WILL RECEIVE ~
FREE Technical Support
New Product Information
N Router
FREE Firmware Upgrades Special Offers & Promotions
3G/4G Ready
cradlepoint.com/register
What’s Included In The Box
•
•
•
Mobile Broadband N Router
Quick Start Guide
Ethernet Cable
Power Adapter
•
There Are Two Ways To Set Up An MBR900 Router:
2) Wired Connection using Cable/DSL Internet Service
Connect power and insert one end of your Ethernet cable to the WAN port. Insert the
other end of the Ethernet cable into your Internet service provider's modem. It may take
a minute or two for the MBR1000 to initialize. Open your web browser. You can now
access the Internet.
1) Wireless Setup using a Mobile Broadband
(cellular) Data Modem
Connect Power Supply and insert USB modem.*
Note: CradlePoint recommends that WiFi security be setup at this point.
Then, follow the instructions below to establish an wireless internet connection.
See the “Setting WiFi security on your CradlePoint Router” section of this guide.
Ethernet Cable
Internet Service (ISP)
Ethernet Cable
Power
Supply
Power
Supply
USB
USB
Modem
* Mobile Broadband Card not included.
See your Mobile Broadband Service Provider for details.
Establishing a Wireless Internet Connection
Port Panel
1) Identify the MBR900
Windows XP
Open your computer’s WIRELESS
MBR900-xxx
NETWORK CONNECTION to associate
with the router’s Wireless Access Point.
This is typically completed by opening
VIEW AVAILABLE NETWORKS
window. After you have highlighted the
MBR900-xxx, click CONNECT.
WAN Port
WiFi On/Off
Power On/Off
Reset Button
AC Adapter
Antennas
4-LAN Ports
Windows Vista
Open CONNECT TO A NETWORK by
MBR900-xxx
clicking the Start button, and then
click CONNECT TO. You'll see a list
of the wireless networks currently
available. Click on the MBR900-xxx
network, and then click CONNECT.
Mac
Open your wireless connection list
by clicking the AIRPORT wireless
icon on your menu bar. Click the
MBR900-xxx.
LED Status Lights
MBR900-xxx
Signifies the MBR1000 has power.
Signifies the routers WiFi radio is “On”.
Blinking indicates traffic.
–
1 4
Signifies that a connection is made on
respective LAN port. Blinking indicates
traffic over the port.
2) Connect To the Internet
Indicates a recognizable cellular device is
connected to the router.
1) Using either a Windows or Mac platform, open a
browser window. A default CradlePoint page will
appear asking for a password.
Red No Connection is being Attempted
or Device not Recognized or Supported
Signifies that a connection is made on the WAN
port. Blinking indicates traffic over the port.
Note: The WAN port will turn on even if plugged into a computer. It is for Internet
connections only (i.e. DSL/Cable modems).
Orange (Blinking) Modem is Dialing
Orange (Solid) Modem is Recognized
Green (Blinking) Modem is Negotiating
Green (Solid) Modem is Connected
2) The password is the last six digits of the MAC
address shown on the box label and on the
bottom of the router. This is a unique number
identifying your router.
Stands for "WiFi Protected Setup." When you
push it, the router goes into setup mode for 90
seconds; in which time, it looks for other WPS
devices that are also in setup mode. When
they find each other, they setup WPA-Personal
Security between the 2 WiFi devices.
3) Once you have correctly entered your password,
click “OK”. You can now access the Internet.
While in Signal Strength button is
pressed, the WAN, WiFi, WPS and
Modem LEDs display the strength of
the Mobile Broadband Modem signal.
Note: CradlePoint recommends that WiFi security
be setup at this point. See the “Setting WiFi security
on your CradlePoint Router” section of this guide.
Note: While in SGNL mode, you are still able to enter WPS mode, but the WPS LED
will not be used.Also, if you enter SGNL mode while in WPS mode,WPS will continue
normally but the WPS LED will not be used.
|