Fisher Paykel GB IE User Manual

Installation instructions  
and User guide  
Freestanding cooker  
OR90 double oven models  
GB IE  
1
Contents  
Safety and warnings  
2
6
Installation instructions  
Introducing your cooker  
Using your gas cooktop  
Cooktop troubleshooting  
Using your multifunction oven for the first time  
Clock and timer  
Using your oven  
Cooking functions  
Automatic cooking  
Using your compact oven for the first time  
Using your compact oven  
Cooking functions  
Using the dish-warming shelf  
Care and cleaning  
16  
17  
21  
22  
23  
24  
25  
27  
28  
29  
29  
30  
31  
39  
Warranty and service  
Important!  
SAVE THESE INSTRUCTIONS  
The models shown in this User Guide may not be available in all markets and are  
subject to change at any time. For current details about model and specification  
availability in your country, please visit our local website listed on the back cover  
or contact your local Fisher & Paykel dealer.  
2
Safety and warnings  
Installation  
WARNING!  
Electrical Shock Hazard  
Always disconnect the cooker from the mains electricity supply before  
carrying out any maintenance operations or repairs.  
Failure to do so may result in death or electrical shock.  
WARNING!  
Cut Hazard  
Take care - panel edges are sharp.  
Failure to use caution could result in injury or cuts.  
Important safety precautions  
General  
To avoid hazard, follow these instructions carefully before installing or using this product.  
Please make this information available to the person installing the product as it could reduce  
your installation costs.  
Installation must comply with your local building and electricity regulations.  
Failure to install the cooker correctly could invalidate any warranty or liability claims.  
Some appliances have a protective film. Remove this film before using the cooker.  
Electrical  
This cooker is to be installed and connected to the electricity supply only by an authorised person.  
If the installation requires alterations to the domestic electrical system call a qualified electrician.  
He should also check that the electrical system is suitable for the electricity drawn by the cooker.  
The appliance must be connected to the mains, checking that the voltage corresponds to the  
value given in the rating plate and that the electrical cable sections can withstand the load  
specified on the plate.  
A suitable disconnection switch must be incorporated in the permanent wiring, mounted and  
positioned to comply with the local wiring rules and regulations. The switch must be of an  
approved type installed in the fixed wiring and provide a 3 mm air gap contact separation in all  
poles in accordance with the local wiring rules.  
The switch must always be accessible.  
The power supply cable must not touch any hot parts and must be positioned so that it does not  
exceed 75 OC at any point.  
3
Safety and warnings  
To connect the cooker to the mains, do not use adapters, reducers or branching devices as they  
can cause overheating and burning.  
This cooker must be connected to a suitable double pole control unit adjacent to the cooker. No  
diversity can be applied to this control unit.  
The cooker must be earthed.  
Gas  
This cooker is supplied for use with natural gas only, and cannot be used on any other gas  
without modification. See ‘Gas installation’ for modification to other gas types.  
This cooker can only be installed in a room with adequate ventilation. See the ‘Ventilation  
requirements’ in the installation instructions .  
4
Safety and warnings  
Operation  
Your freestanding cooker has been carefully designed to operate safely during normal cooking  
procedures. Please keep the following guidelines in mind when you are using it:  
WARNING!  
Explosion Hazard  
Do not store flammable materials such as gasoline near the cooktop.  
Do not store flammable material in the ovens or in the storage compartment.  
Do not spray aerosols near the cooktop during use.  
Failure to do so may result in death or serious injury.  
WARNING!  
Electrical Shock Hazard  
Switch the cooker off at the wall before replacing fuses or the oven lamp.  
Failure to do so may result in death or electrical shock.  
WARNING!  
Hot Surface Hazard  
Accessible parts will become hot when this cooker is in use.  
To avoid burns and scalds keep children away.  
Do not touch hot surfaces inside the ovens.  
Use oven mitts or other protection when handling hot surfaces such as oven  
shelves or dishes.  
Take care when opening the oven doors.  
Let hot air or steam escape before removing or replacing food.  
Do not touch the cooktop components, burners, trivets/pan supports or the  
base when hot.  
Before cleaning, turn the cooker off and make sure it is cool.  
Failure to do so could result in burns and scalds.  
5
Safety and warnings  
Important safety precautions  
Isolating switch: make sure this cooker is connected to a circuit which incorporates an isolating  
switch providing full disconnection from the power supply.  
Household appliances are not intended to be played with by children.  
Children, or persons with a disability which limits their ability to use the appliance, should have a  
responsible person to instruct them in its use. The instructor should be satisfied that they can use  
the appliance without danger to themselves or their surroundings.  
Safe food handling: leave food in the oven for as short a time as possible before and after  
cooking. This is to avoid contamination by organisms which may cause food poisoning. Take  
particular care during warmer weather.  
Do not place aluminium foil, dishes, trays, water or ice on the oven floor during cooking as this  
will irreversibly damage the enamel.  
Do not line the walls with aluminium foil.  
Do not stand on the doors, or place heavy objects on them.  
Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven door glass since  
they scratch the surface, which may result in shattering of the glass.  
Do not use a steam cleaner to clean any part of the cooker.  
Do not use an asbestos mat or decorative covers between the flame and the saucepan as this may  
cause serious damage to your cooktop.  
Do not place aluminium foil or plastic dishes on the cooktop burners.  
Do not let large saucepans or frying pans overlap the bench as this can deflect heat onto your  
benchtop and damage the surface.  
Do not let large saucepans, frying pans or woks push any other pans aside. This could make them  
unstable or deflect heat onto your benchtop and damage the surface.  
Saucepan handles may be hot to touch. Ensure saucepan handles do not overhang other gas  
burners that are on. Keep handles out of reach of children.  
If the electrical supply cord is damaged, it must only be replaced by an authorised person.  
This cooker is not to be used as a space heater.  
The use of a gas cooking appliance results in the production of heat and moisture in the room in  
which it is installed. Ensure the kitchen is well ventilated. Keep natural ventilation holes open or  
install a mechanical ventilation device (mechanical extractor hood).  
Prolonged intensive use of the appliance may call for additional ventilation, for example opening  
of a window, or more effective ventilation, for example increasing the level of mechanical  
ventilation where present.  
6
Installation instructions  
Figure 1 Cooker dimensions and capacity  
The cooker must be installed by a qualified technician and in compliance with local  
safety standards. This cookers has class “2/1” overheating protection so that it can be installed  
next to a cabinet.  
If the cooker is installed adjacent to furniture which is higher than the gas hob cooktop, a  
gap of at least 200 mm must be left between the side of the cooker and the furniture.  
The furniture walls adjacent to the  
cooker must be made of material  
resistant to heat.The veneered  
synthetical material and the glue used  
must be resistant to a temperature  
of 90°C in order to avoid ungluing or  
deformations.  
The cooker may be located in a  
kitchen, a kitchen/diner or bed-sitting  
room but not in a room containing a  
bath or shower.  
Curtains must not be fitted  
immediately behind appliance or  
within 500 mm of the sides.  
m
m
00  
5
A
U
T
O
If the cooker is located on a pedestal  
it is necessary to provide safety  
measures to prevent falling out.  
It is essential that the cooker is  
positioned as stated.  
Figure 2 Correct distances from cooker  
7
Installation instructions  
Fitting the adjustable feet  
Important!  
Using the supplied adjustable feet is MANDATORY. For safety reasons and to ensure adequate  
ventilation, the cooker chassis MUST NOT sit directly on the floor, a plinth, or other support surface.  
The adjustable feet must be fitted to the base of the cooker before use.  
Rest the rear of the cooker on a piece of the polystyrene packaging exposing the base for the  
fitting of the feet.  
Fit the four legs by screwing them tight into the support base as shown.  
Figure 3 Location of feet  
Figure 4 Top of feet screwed in tightly  
Levelling the cooker  
Level the cooker by screwing the bottom of the feet in or out, as shown.  
Figure 5 Levelling the cooker  
8
Installation instructions  
Moving the cooker  
Important!  
Two people must always raise the cooker, as  
shown, to prevent damaging the adjustable feet.  
Do not lift the cooker by the door handles.  
DO NOT DRAG the cooker. Lift the feet clear of the  
floor.  
Figure 6 Correctly raising the cooker  
Figure 7 Incorrectly moving the cooker  
Figure 8 Incorrectly raising the cooker  
Backguard  
C
B
Before installing the cooker, assemble the  
backguard “C” .  
The backguard “C” can be found packed  
at the rear of the cooker.  
Before assembling remove any protective  
film/adhesive tape.  
Remove the two spacers “A” and the  
screw “B” from the rear of the cooktop.  
Assemble the backguard as shown and  
fix it by screwing the central screw “B”  
and the spacers “A.  
A
Figure 9 Assembling  
the backguard  
9
Installation instructions  
Stability bracket (GB & IE only)  
We recommend a stability bracket is fitted to the cooker.  
You can buy the type of bracket shown here from most plumbing and DIY shops.  
Existing slot in  
rear of cooker  
Brackets  
Dotted line showing the  
position of cooker when fixed  
Outline of cooker  
backplate at the  
engagement slot  
Wall fixing  
Floor fixing  
Dimensions are in millimetres  
Figure 10 Fitting a stability bracket  
10  
Installation instructions  
Ventilation requirements (GB & IE only)  
The appliance should be installed into a room or space with an air supply in accordance with BS  
5440-2:2000.  
For rooms with a volume of less than 5 m3 - permanent ventilation of 100 mm2 free area will be  
required.  
For rooms with a volume of between 5 m3 and 10 m3 a permanent ventilation of 50 cm2 free area  
will be required unless the room has a door which opens directly to the outside air in which case  
no permanent ventilation is required.  
For rooms with a volume greater than 10 m3 - no permanent ventilation is required.  
Important!  
Regardless of room size, all rooms containing the appliance must have direct access to the outside air via  
an openable window or equivalent.  
Where there are other fuel burning appliances in the same room, BS 5440-2:2000 should be  
consulted to determine the correct amount of free area ventilation requirements.  
Gas installation (GB & IE only)  
Important!  
This cooker uses NATURAL GAS only and cannot be used on any other gas without modification. This  
appliance is manufactured for conversion to LPG if required. If the injectors are not supplied they can be  
obtained from the After-Sales Service.  
Installation and service regulations  
Important!  
This appliance must be installed and serviced only by a suitably qualified and registered person, and in  
accordance with the current editions of the following standards and regulations or other locally applicable  
regulations:  
Gas Safety (Installation and Use) Regulations  
Building Regulations  
British Standards  
Regulations for Electrical Installation  
Failure to install the appliance correctly could invalidate any manufacturer’s warranty  
and lead to prosecution under the above-quoted regulation.  
Gas connection  
The installation of the cooker to Natural Gas or LP Gas must be carried out by a qualified  
gas engineer. Installers shall take due account of the provisions of the relevant British  
Standards Code of Practice, the Gas Safety Regulations and the Building Standards (Scotland)  
(Consolidation) Regulations issued by the Scottish Development Department.  
Note: It is recommended that the gas connection to the cooker is installed with a flexible  
connecting tube made to BS 5386.  
11  
Installation instructions  
Installation to Natural gas  
Installation to Natural Gas must conform to the Code of Practice, etc. The supply pressure for  
Natural Gas is 20 mbar.  
Installation to Liquid Petroleum gas  
This appliance must only be connected to LPG after an LPG conversion kit has been fitted. The  
installation must conform to the relevant British Standards.  
Important!  
Only a suitably qualified and registered person may convert the appliance to a different gas type.  
When using Butane gas a supply pressure of 28 -30 mbar is required.  
When using Propane gas a supply pressure of 37 mbar is required.  
Notes:  
Flexible hoses can be used where the sited ambient temperature of the hose does not exceed  
70°C. These hoses must be manufactured in accordance with BS669 part 1 and be of the correct  
construction for the type of gas being used.  
Gas hoses designed for natural gas MUST NOT be used for supplying LPG gas (LPG gas hoses can  
be identified by a either a red band or stripe on the rubber outer coating of the hose).  
The hose should not be crushed or trapped or be in contact with sharp or abrasive edges. It  
should also not be subjected to corrosion by acidic cleansing agents.  
To connect the gas supply:  
1
Fit the 1/2” BSP (female) connector (supplied with the cooker in a separate kit) to the gas inlet at  
the rear of the cooker interposing the gasket. Check the correct positioning of the connector as  
shown and always use two suitable spanners (Fig 11b).  
Connect the gas supply to the right or left gas inlet at the rear  
of the cooker. The pipe is not to cross the cooker.  
2
3
4
5
Close the unused end inlet pipe with a plug, interposing the  
gasket (Fig. 11a - Fig. 11b).  
To avoid damage to the appliance gas rail inlet pipe tighten  
the fittings using two suitable spanners (Fig. 11b).  
Using a suitable leak detection fluid solution (e.g. Rocol)  
check each gas connection one at a time by brushing the  
solution over the connection. The presence of bubbles will  
indicate a leak. If there is a leak, tighten the fitting and then  
recheck for leaks.  
Plug  
Figure 11a Gas  
supply inlets  
IMPORTANT!  
Do not use a naked flame to test for leaks.  
Cooker manifold  
Manifold male  
pipe fitting  
1/2” G cylindrical  
(ISO 228-1) male  
Gasket ( )  
*
1/2” G cylindrical  
(ISO 228-1) female  
Connector ( )  
*
Figure 11b  
Connecting the  
gas  
1/2” BSP (female)  
(
) Supplied with the appliance in a separate kit.  
*
12  
Installation instructions  
Rear wall  
Rear wall  
Suggested area for gas  
mains connection  
Figure 12 Gas mains connection area  
Replacement of burner injectors  
If the injectors are not supplied, contact the Fisher & Paykel Authorised Service Centre.  
Select the injectors to be replaced according to the “Table for the choice of the injectors.  
To replace the injectors  
Remove pan supports and burners from the cooktop. Using a wrench substitute the  
nozzle injectors with those most suitable for the kind of gas for which it is to  
be used. The burners are designed so that adjustment of primary air is not required.  
Injector  
Injector  
Figure 13 Auxiliary, semi-rapid and rapid burner  
Figure 14 Triple ring wok burner  
13  
Installation instructions  
Adjusting The Minimum Burner Setting  
Check whether the flame spreads to all burner ports when the burner is lit with the gas tap set to  
the minimum position. If some ports do not light, increase the minimum gas rate setting.  
Check whether the burner remains lit even when the gas tap is turned quickly from the  
maximum to the minimum position. If the burner does not remain lit, increase the minimum gas  
rate setting.  
To adjust the minimum gas rate setting:  
Turn on the burner  
Turn the tap to the MINIMUM position  
Take off the knob  
With a small flat screwdriver turn the screw (accessible through the hole in the microswitch - see  
the following figure) to the correct regulation.  
Note: for G30/G31 gas, completely tighten the screw.  
regulation screw  
Figure 15 Adjusting the minimum burner setting  
14  
Installation instructions  
Table for the choice of the injectors  
Cat: II 2H3+  
GB  
IE  
BURNERS  
NOMINAL  
POWER  
[KW]  
REDUCED  
POWER  
[KW]  
G 30 - 28-30 mbar  
G 31 - 37 mbar  
G 20 - 20 mbar  
Ø INJECTOR  
[1/100 mm]  
Ø INJECTOR  
[1/100 mm]  
AUXILIARY  
SEMIRAPID  
RAPID  
1,00  
1,75  
3,00  
3,50  
0,30  
0,45  
0,75  
1,50  
50  
65  
85  
95  
72 (X)  
97 (Z)  
115 (Y)  
135 (T)  
TRIPLE-RING WOK  
Lubrication of the gas taps  
A qualified technician must lubricate the gas taps.  
Important!  
All intervention regarding installation maintenance and conversion of the appliance must be fulfiled with  
original factory parts.  
The manufacturer declines any liability if these correct parts are not used.  
15  
Installation instructions  
Connecting the feeder cable  
To connect the feeder cable to the cooker:  
Remove the screws securing the  
cover “A” on the rear of the cooker.  
Feed the supply cable through the  
cable clamp “D. See the ‘Feeder cable  
section’ following for the correct size for the  
cable.  
Connect the wires to the terminal  
block “B” as shown in the diagram; or  
connect the phase wires to the terminal  
block “B” and the earth wire to the terminal  
PE as shown.  
PE  
N
L
D
B
Take up any slack in the cable and  
secure with the cable clamp “D.  
Replace the cover “A.  
A
N.B. The earth conductor must be left  
about 3 cm longer than the others.  
Figure 16a Connecting the feeder cable  
230 V  
Feeder cable section  
“TYPE H05RR-F”  
230V  
3 x 2.5 mm2 (**)  
L1  
N
PE  
(**) - Connection with wall  
box connection.  
(L2)  
PE  
N
L
Earth  
Neutral  
Live  
Figure 16b Connecting the feeder cable  
16  
Introducing your cooker  
Thank you for buying a Fisher & Paykel freestanding cooker. Once it is installed and ready to use,  
you will want to know everything about it to make sure you get excellent results right from the  
start. This guide introduces you to all its special features. We recommend you read the whole  
guide before using your new cooker, for both safety and cooking success.  
For more information, go to www.fisherpaykel.com  
9
8
11  
10  
15  
14  
6
7
1
2
3
4
5
12  
13  
Figure 17 Cooker control panel  
Gas cooktop controls:  
Front left (rapid) burner control knob  
Compact oven controls:  
12 Function knob  
1
2
Rear left (semi-rapid) burner control  
knob  
Central (triple ring wok) burner control  
knob  
Rear right (semi-rapid) burner control  
knob  
Front right (auxiliary) burner control  
knob  
13 Temperature knob  
14 Temperature indicator light  
15 Oven on light  
3
4
5
Main oven controls:  
Function knob  
Temperature knob  
Control buttons  
Clock display  
6
7
8
9
10 Temperature indicator light  
11 Oven on indicator light  
17  
Using your gas cooktop  
2
4
2
Figure 18 Cooktop layout  
3
1
1
2
3
4
Auxillary burner  
Semi-rapid burner  
Rapid burner  
Triple ring wok burner  
Gas burners  
The knob controls the flow of gas through the safety tap.  
=
=
=
closed valve  
maximum aperture or flow  
minimum aperture or flow  
0
You can choose to cook at any heat between and  
, but never between  
and OFF.  
Figure 19 Burner control knob  
18  
Using your gas cooktop  
Before using your cooktop  
Before using your new cooktop, please:  
Read this user guide, taking special note of the safety and warnings section.  
Turn the cooker on.  
Make sure all controls are turned off.  
Lighting the cooktop  
1
2
Choose the control knob for the burner you want to use.  
Press the knob down gently and turn it anticlockwise to the  
burners will spark.  
position. The ignitors on all the  
Hold down the knob for approximately ten seconds after the burner has lit. Releasing the knob  
too soon will extinguish the flame.  
3
Adjust the flame anywhere between the  
and OFF.  
and  
positions. Do not adjust the flame between  
Note: If the burner does not light within 15 seconds, turn the control knob off and wait at least  
one minute before trying again.  
To switch the burner off, turn the knob clockwise until you hear the safety click.  
After use, always turn the knobs to the off position.  
Flame failure safety feature  
The flame failure probe cuts off the gas supply to the burner if the flame is blown out.  
When lighting the burner on flame failure models, hold down the knob for approximately ten  
seconds after the burner has lit. Releasing the knob too soon will extinguish the flame.  
If the flames are accidentally extinguished, turn off the burner and do not try to light it again for  
at least one minute (to allow the gas to disperse).  
19  
Using your gas cooktop  
If the cooktop does not light  
If the cooktop does not light, check that:  
The cooker is switched on.  
The gas is turned on.  
You have held down the knob for at least ten seconds.  
The ignitors are sparking. If the ignitors are not sparking, they may be dirty or wet. Clean them  
with a toothbrush and methylated spirits, as shown.  
Flame failure probe  
Ignitor  
Figure 20 Cleaning the probe and ignitor  
If the flame is irregular  
If the flame is yellow or irregular, check that the burner parts, including the burner cap, are:  
Clean and dry.  
Positioned correctly. See ‘Care and cleaning.  
See also ‘Troubleshooting.  
20  
Using your gas cooktop  
Choosing a burner  
Use flat-bottomed pans, and make sure that they match your burner, as shown in the following  
table. A small pot on a large burner is not efficient.  
Diameters of pans which may be used on the cooktop  
Burners  
Minimum  
12 cm  
Maximum  
14 cm  
Auxiliary  
Semi-rapid  
Rapid  
16 cm  
24 cm  
24 cm  
26 cm  
Triple ring wok  
26 cm  
28 cm  
Maximum diameter for woks 36 cm  
Figure 21a Correct and incorrect matching  
Figure 21b Efficient and inefficient saucepan bottoms  
Wok stand  
CORRECT  
WRONG  
Figure 22 Correct placement of wok stand  
Important!  
Using a wok without the stand may cause the burner to operate incorrectly.  
Do not use the stand for ordinary, flat-bottomed saucepans.  
The wok stand MUST BE PLACED ONLY over the pan support for the triple ring wok burner.  
The cooktop becomes very hot during operation. Keep children well out of reach.  
21  
Cooktop troubleshooting  
Problem  
Possible solutions  
My cooktop burners do not light  
Check the cooker is switched on.  
Check the gas supply valve is turned on and the  
supply to the house is working. You should hear the  
gas when you turn a burner on.  
The ignitors may be dirty. Clean them with a  
toothbrush and methylated spirits.  
The burner parts may not be located properly. Check  
the assembly and make sure the burner cap is sitting  
flat.  
My burner flames are yellow or  
hard to start  
The burner parts may not be located properly. Check  
the assembly and make sure the burner cap is sitting  
flat.  
If you use bottled gas this may indicate you are  
getting near the end of the bottle.  
Check the burner parts are clean and dry.  
The gas pressure may not be at the correct level.  
Check with your service person or installer.  
Your cooker may not be set up for the gas you are  
using. Check this with your service person or installer.  
One of my burners has an uneven Check the burner parts are clean and dry. Check the  
flame assembly and make sure the burner cap is sitting flat.  
The flame goes out at low settings The gas supply pressure may be low. Check this with  
your service person or installer.  
The low setting may have been adjusted incorrectly.  
Check this with your service person or installer.  
My burners do not turn down  
much (when running on bottled  
gas or LPG)  
Your cooktop may not have been adjusted correctly.  
Check this with your service person or installer.  
The flame tips are very yellow  
Call your service person to service the cooker.  
Call your service person to service the cooker.  
Call your service person to service the cooker.  
There are objectionable odours  
The flame appears to lift off the  
burner  
There is an electricity failure  
If there is an electricity failure, you can still use your  
cooktop. Light the burners by holding a match close  
to the side of the burner and turning the control  
knob to the High position. Wait until the flame is  
burning evenly before adjusting.  
22  
Using your multifunction oven for the first time  
Using your oven for the first time  
Clock display  
Function  
knob  
Temperature  
knob  
Control buttons  
Figure 23 Main oven controls  
Before using your new oven, please:  
1
2
3
4
Read this user guide, taking special note of the ‘Safety and warnings’ section.  
Remove all accessories and packaging.  
Set the clock. The oven will not work until the clock has been set.  
Condition the oven:  
Put in the shelves and trays. Fit them between  
the metal runners, with the safety stop notch down  
and at the back. (If the shelf supports are not  
already fitted, see ‘Care and cleaning’  
for how to do this).  
Heat the oven on maximum for:  
60 minutes in the  
30 minutes in the  
15 minutes in the  
position  
position  
position  
5
Wipe out the oven with a damp cloth and mild detergent,  
and dry thoroughly.  
Figure 24 Correct position of shelves and pan  
23  
Clock and timer  
Buttons:  
Timer  
Cooking time  
End of cooking time  
Decreases the number shown on the display or  
changes the volume of the beeps  
Increases the number shown on the display  
Illuminated symbols:  
Figure 25 Clock display and control buttons  
A
A
- flashing - oven in automatic position but not set  
- steady illumination - oven set for automatic cooking  
Cooking taking place  
Timer in operation  
Setting the clock  
.
When first connected, or after a power failure, ‘0 00’ will flash on the display.  
To set the clock, press the and buttons together and then the and  
buttons.  
Note: Changing the time will delete any automatic program.  
Using the timer  
The timer can be set for up to 23 hours and 59 minutes.  
To set the timer, press the  
To check the remaining time press the  
When the time is up, the timer will beep. Press the  
button, then the  
and  
buttons.  
button.  
button to turn it off.  
and buttons together.  
Note: if ‘A’ is flashing on the display, press the  
Setting the timer volume  
You can select from three volume levels by pressing the  
button.  
24  
Using your oven  
Figure 26 Function knob  
Figure 27 Temperature knob  
1
2
Select the function using the function knob. The oven lights will come on.  
Select the temperature using the temperature control knob. The oven temperature indicator  
light, above the temperature knob on the control panel, will glow until the oven has reached the  
set temperature, and then it will go out.  
When you have finished cooking, turn the function and temperature control knobs to the off O  
3
position.  
Note: if ‘A’ is flashing or steadily illuminated on the display, press the  
together.  
and  
buttons  
25  
Cooking functions  
OVEN LAMP  
Only the oven light comes on. It remains on in all the cooking functions.  
BAKE  
The upper and lower heating elements come on. BAKE is the traditional method of cooking. It is  
best to cook on only one shelf at a time in this function.  
GRILL  
The grill at the top of the oven comes on. Preheat for two minutes. Use with the oven door  
closed and the temperature knob between 50° and 225°C for 15 minutes, then to position 175°C..  
Do not grill for longer than 30 minutes at any one time.  
DEFROST  
Only the oven fan comes on. Use with the temperature knob set to O. The fan circulates air  
around the oven, speeding up the defrosting process by approximately 30%.  
Note: this function is not for cooking food.  
FAN FORCED  
The circular heating element and the fan come on. The oven set on FAN FORCED can cook  
several different foods together. Use FAN FORCED for multi-shelf cooking.  
FAN GRILL  
Both the grill and the fan come on. Use with the oven door closed and the temperature knob  
between 50 °C and175 °C max. Do not grill for longer than 30 minutes at any one time.  
WARM  
The upper element, the circular element and the fan come on. Set between 50 OC and 140 OC.  
Note: this function is not for cooking food.  
26  
Cooking functions  
FAN BAKE  
The upper and lower heating elements and the fan come on.  
Important!  
Safe food handling: leave food in the oven for as short a time as possible before and after cooking or  
defrosting. This is to avoid contamination by organisms which may cause food poisoning. Take particular  
care during warmer weather.  
Notes on baking and roasting:  
Only use the fat filter for roasting. Remove before baking. Always clean the filter after  
cooking.  
Preheat the oven before baking.  
Do not place anything, including water or ice, on the oven floor.  
Figure 28 Fat filter  
27  
Automatic cooking  
Use automatic cooking to automatically turn the oven on, cook, and then turn the oven off.  
1
2
3
4
5
Check the clock shows the correct time.  
Select the function and temperature. The oven will come on.  
Decide how long the food will take to cook, allowing time for preheating if necessary.  
.
Press the  
Select the time you would like the oven to turn off by pressing the  
the buttons.  
button. 0 00 will show. Using the  
buttons, set the cooking time.  
button, and then using  
If there is time to wait before cooking starts, the current time of day and A will show in the clock  
display. The oven temperature and function lights will go out and the oven will switch off but is  
now set for automatic cooking.  
If you are already at home to turn the oven on and only want the oven to turn off automatically,  
start cooking as normal, then follow step 4 or step 5 to set a time to stop the oven.  
When automatic cooking starts,  
will be displayed and the oven will turn on.  
To see the remaining cook time, press the  
To see the set stop time, press the button.  
button.  
To cancel automatic cooking at any time, press the  
temperature and function knobs to the off O position.  
and  
buttons together and turn the  
When the stop time is reached, the oven will turn off, the timer will beep and  
A
will flash:  
buttons  
To stop the beeping and return the oven to manual mode, press the  
and  
together.  
Turn the temperature and function knobs to the off position.  
O
Important!  
Safe food handling: leave food in the oven for as short a time as possible before and after  
cooking. This is to avoid contamination by organisms which may cause food poisoning. Take  
particular care during warmer weather.  
28  
Using your compact oven for the first time  
Before using your new oven, please:  
1
2
3
Read this user guide, taking special note of the ‘Safety and warnings’ section.  
Remove all accessories and packaging.  
Condition the oven:  
Put in the shelf and tray. Make sure you fit the shelf  
so that the safety catch, which stops it sliding out,  
faces down.  
Heat the oven on maximum for:  
60 minutes in the  
15 minutes in the  
position  
position  
4
Wipe out the oven with a damp cloth and mild detergent,  
and dry thoroughly.  
Figure 29 Correct position of shelves and pan  
Note: If the shelf supports are not already fitted,  
see ‘Care and cleaning’ for how to do this.  
29  
Using your compact oven  
Figure 30 Compact oven function and temperature knobs  
1
2
Select the function using the function knob. The oven lights will come on.  
Select the temperature using the temperature control knob. The oven temperature indicator  
light, above the temperature knob on the control panel, will glow until the oven has reached the  
set temperature, and then it will go out.  
3
When you have finished cooking, turn the function and temperature control knobs to the off O  
position.  
Cooking functions  
OVEN LAMP  
Only the oven light comes on. It remains on in all the cooking functions.  
BAKE  
The upper and lower heating elements come on. BAKE is the traditional method of cooking. It is  
best to cook on only one shelf at a time in this function.  
GRILL  
The grill at the top of the oven comes on. Preheat for two minutes. Use with the oven door  
closed and the temperature knob between 50° and 225°C for 15 minutes, then to position 175°C.  
Do not grill for longer than 30 minutes at any one time.  
Notes on baking:  
Preheat the oven before baking.  
Do not place anything, including water or ice, on the oven floor.  
30  
Using the dish-warming shelf  
The dish-warming shelf can be used to hold dishes or for cooking. If you want to warm plates,  
put the oven on bake at about 60 °C. Take care when removing plates, as they can get hot.  
To use the shelf to hold dishes  
Turn it with the plate supports facing up.  
Fit the shelf between the metal runners on the lowest shelf support, with the safety stop notch  
down and at the back.  
To use the shelf for cooking  
Turn the shelf with the plate supports facing down.  
Fit the shelf between the metal runners, with the other safety notch down and at the back.  
Figure 31a Using the shelf to hold dishes  
Figure 31b Using the shelf for cooking  
31  
Care and cleaning  
Important!  
Before you start cleaning your cooker, please:  
Read these cleaning instructions and the ‘Safety and warnings’ section at the start of this user  
guide.  
Turn the cooker off at the wall.  
Make sure the cooker is a safe temperature to touch.  
Do not use a steam cleaner.  
Do not keep flammable substances in the ovens or storage compartment.  
General advice  
Wipe out the ovens after every use.  
Wipe up spills. Avoid leaving alkaline or acidic substances (such as lemon juice or vinegar) on  
the oven surfaces.  
Do not use cleaning products with a chlorine or acidic base.  
Cleaning the outside of the cooker  
Important!  
Do not use abrasive cleaners, cloths or pads on the outside surfaces.  
Immediately wipe off any caustic cleaners if they are spilled onto the oven door handles.  
Wipe the outside surfaces often, using warm water and a mild household detergent. The  
stainless steel may also be cleaned with a suitable cleaner and polish.  
Note: if you choose to use a commercial stainless steel cleaner, please read the label to make  
sure it does not contain chlorine compounds as these are corrosive and may damage the  
appearance of your cooker.  
Cleaning the gas cooktop  
Maintenance Period  
Daily  
Description  
Clean gas cooktop as per following instructions.  
Remove all burner parts, and clean using a non-abrasive  
detergent. Rinse in cold water, dry thoroughly, and replace.  
Clean the ignitor and probe carefully, using a toothbrush  
and methylated spirits.  
Monthly  
Contact your local authorized gas Service Agent to perform  
a thorough check on all gas components on the gas  
cooker.  
Every 3-4 years  
32  
Care and cleaning  
Burner parts and pan supports  
You can remove and clean these parts with hot soapy water or non-abrasive detergents. Clean  
spills regularly before they become burnt on. Do not wash these parts in a dishwasher.  
After cleaning, check that the burners and their flame spreaders are dry before replacing  
correctly.  
It is very important to check that the burner flame spreader and the cap have been correctly  
positioned. Failure to do so can cause serious problems.  
Note: To avoid damage to the electric ignition do not try to light the cooktop when the burners  
are not in place.  
Replacing the burners  
Check that:  
The ignitor is always clean to ensure trouble-free sparking.  
The probe is always clean to ensure correct operation of the safety valves.  
Note: both the ignitor and probe must be very carefully cleaned using a toothbrush and  
methylated spirits.  
Cap  
Flame  
spreader  
Probe  
Ignitor  
Figure 33 Replacing the auxiliary,  
rapid and semi-rapid burners  
Figure 32 Auxiliary, rapid and semi-rapid burner parts  
33  
Care and cleaning  
Replacing the triple ring wok burner  
To replace the wok burner, fit the burner ring to the housing as shown by the arrow in the figure  
following. Make sure the burner is not able to rotate.  
Probe  
Ignitor  
Figure 35 Replacing the triple ring wok burner  
Figure 34 Triple ring wok burner parts  
Gas taps  
If you have problems with the gas taps, call your Authorised Service Centre.  
34  
Care and cleaning  
Cleaning the inside of your ovens  
Do not use abrasive cleaners, cloths or pads to clean the enamel.  
Do not use any oven cleaners, abrasive cleaners, ammonia-based cleaners, products containing  
acids or alkalis, or detergents on the catalytic panels (not supplied with all models).  
Fig.36 Removing the side racks  
To make cleaning easier, you can remove the side racks, the oven door, and the fat filter. The grill  
element is self-cleaning.  
35  
Care and cleaning  
Cleaning the enamel cavity  
Clean the enamel on the inside of the oven when it has cooled down, using household  
detergents or an ammonia-based cleaner. You may use ‘off the shelf’ oven cleaners, if you  
carefully follow the manufacturers’ instructions.  
Cleaning the fat filter  
Clean the fat filter after every use. If the filter is not cleaned, it will block and shorten the life of  
the fan element. For normal soiling, place the filter in a dishwasher on normal wash. If the filter  
is very dirty, place in a saucepan with either two tablespoons of clothes washing powder, or one  
tablespoon of dishwashing powder. Bring to the boil and leave to soak for at least 30 minutes.  
Rinse the filter in clean water and dry.  
Fig.37 Fat filter  
36  
Care and cleaning  
Cleaning the oven door glass  
Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven door glass since  
they scratch the surface, which may result in shattering of the glass.  
The inner glass door panel can easily be removed for cleaning by unscrewing the two screws, as  
shown.  
When re-assembling ensure that the inner glass is correctly positioned and do not over-tighten  
the screws.  
Fig.38 Cleaning the oven door glass  
Storage compartment  
The storage compartment is accessible through the pivoting panel.  
Important!  
Do not store flammable material in the ovens or in the storage compartment.  
Fig.39 Storage compartment  
37  
Care and cleaning  
Removing the oven door(s)  
The oven door(s) can easily be removed as  
follows:  
Open the door completely.  
The swivel retainers of the rh and lh hinges  
(Fig. 40a) are hooked onto the metal bar  
above them (Fig. 40b).  
Lift the oven door slightly. The notch on  
the bottom of the hinge will disengage  
(Fig. 40c).  
Fig.40a  
Now pull the oven door forwards off the  
appliance. Release both hinge sections  
from the slots (Fig. 40d).  
To replace the door, repeat the above steps  
in reverse order.  
Fig.40b  
Fig.40c  
Fig.40e  
Fig.40d  
38  
Care and cleaning  
Replacing the oven lamp  
Let the oven cavity and the heating elements cool down.  
Remove the protective cover B.  
Unscrew and replace the bulb A with a new one suitable for high temperatures (300°C) with the  
specifications: 230-240V 50 Hz, 15W, E14  
Refit the protective cover.  
Note: Oven bulb replacement is not covered by your warranty.  
A
B
Fig.41 Removing either oven lamp  
39  
Warranty and service  
Before you call for service or assistance ...  
Check the things you can do yourself. Refer to the installation instructions and your user guide  
and check that:  
1
2
Your product is correctly installed.  
You are familiar with its normal operation.  
If after checking these points you still need assistance, please refer to the Service & Warranty  
book for warranty details and your nearest Authorised Service Centre, or contact us through our  
website:  
This cooker has been designed and constructed in accordance with the following  
codes and specifications:  
In Europe:  
Safety requirements of EEC Directive “Gas” 90/396  
- EN 30-1-1  
GB  
IE  
- EN 30-2-1  
- EN 437  
Safety requirements of EEC Directive “Low voltage” 73/23:  
- EN 60335-1 General Requirements for Domestic electrical appliances  
- EN 60335-2-6 Particular Requirements for Domestic electrical cooking appliances  
Safety requirements of EEC Directive “EMC” 89/336:  
- EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3 Electromagnetic Compatibility  
Requirements  
Requirements of EEC Directive 93/68.  
European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE)  
(for European Union countries only)  
GB This appliance is marked according to the European directive 2002/96/EC on Waste Electrical  
and Electronic Equipment (WEEE). By ensuring this product is disposed of correctly, you will help  
prevent potential negative consequences for the environment and human health, which could  
otherwise be caused by inappropriate waste handling of this product.  
The symbol  
on the product, or on the documents accompanying the product, indicates that  
this appliance may not be treated as household waste. Instead it shall be handed over to the  
applicable collection point for the recycling of electrical and electronic equipment. Disposal  
must be carried out in accordance with local environmental regulations for waste disposal.  
For more detailed information about treatment, recovery and recycling of this product, please  
contact your local city office, your household waste disposal service or the shop where you  
purchased the product.  
Copyright © Fisher & Paykel 2009. All rights reserved.  
The product specifications in this booklet apply to  
the specific products and models described at the  
date of issue. Under our policy of continuous product  
improvement, these specifications may change at any  
time. You should therefore check with your Dealer to  
ensure this booklet correctly describes the product  
currently available.  
GB IE  
Freestanding cooker user guide  
Published: 07/2009  
Part No. 599380 C  
F&P Italy Part No. 1102980-ß3  

HP Hewlett Packard Hewlett Packard Computer Monitor L2245W User Manual
Hanns G HW223DPB User Manual
GE Monogram ZET837DBSB User Manual
Emerson EMTV21785 User Manual
Electrolux Cooktop EI36EC45K S User Manual
Cypress CY8C24123 User Manual
Corsair Hydro Series User Manual
Cisco Systems Computer Hardware 7326 User Manual
Asus Computer Hardware P4P800SE User Manual
Abit NF7 M User Manual