Eizo EIZO FlexScan L768 User Manual

SAFETY SYMBOLS  
This manual uses the safety symbols below. They denote critical information. Please read  
them carefully.  
WARNING  
Failure to abide by the information in a WARNING may result in serious injury  
and can be life threatening.  
CAUTION  
Failure to abide by the information in a CAUTION may result in moderate injury  
and/or property or product damage.  
Indicates a prohibited action.  
Indicates to ground for safety.  
Copyright© 2004 EIZO NANAO CORPORATION All rights reserved. No part of this  
manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any  
means, electronic, mechanical, or otherwise, without the prior written permission of EIZO  
NANAO CORPORATION.  
EIZO NANAO CORPORATION is under no obligation to hold any submitted material or  
information confidential unless prior arrangements are made pursuant to EIZO NANAO  
CORPORATION’s receipt of said information. Although every effort has been made to ensure  
that this manual provides up-to-date information, please note that EIZO monitor  
specifications are subject to change without notice.  
ENERGY STAR is a U.S. registered mark.  
Apple and Macintosh are registered trademarks of Apple Computer, Inc.  
VGA is a registered trademark of International Business Machines Corporation.  
DPMS is a trademark and VESA is a registered trademark of Video Electronics Standards  
Association.  
Windows is a registered trademark of Microsoft Corporation.  
PowerManager is a trademark of EIZO NANAO CORPORATION.  
ScreenManager, FlexScan and EIZO are registered trademarks of EIZO NANAO  
CORPORATION in Japan and other countries.  
®
As an ENERGY STAR Partner, EIZO NANAO CORPORATION has determined that  
this product meets the ENERGY STAR guidelines for energy efficiency.  
English  
TABLE OF CONTENTS  
TABLE OF CONTENTS 3  
English  
PRECAUTIONS  
IMPORTANT!  
z This product has been adjusted specifically for use in the region to which it was  
originally shipped. If operated outside the region to which it was originally  
shipped, the product may not perform as stated in the specifications.  
z To ensure personal safety and proper maintenance, please read this section and the  
caution statements on the unit (refer to the figure below).  
[Location of the Caution Statements]  
WARNING  
If the unit begins to emit smoke, smells like something is  
burning, or makes strange noises, disconnect all power  
connections immediately and contact your dealer for advice.  
Attempting to use a malfunctioning unit may result in fire, electric  
shock, or equipment damage.  
Do not open the cabinet or modify the unit.  
Opening the cabinet or modifying the unit may result in fire,  
electric shock, or burn.  
Refer all servicing to qualified service personnel.  
Do not attempt to service this product yourself as opening or  
removing covers may result in fire, electric shock, or equipment  
damage.  
4 PRECAUTIONS  
 
English  
WARNING  
Keep small objects or liquids away from the unit.  
Small objects accidentally falling through the ventilation slots into  
the cabinet or spillage into the cabinet may result in fire, electric  
shock, or equipment damage. If an object or liquid falls/spills into  
the cabinet, unplug the unit immediately. Have the unit checked by  
a qualified service engineer before using it again.  
Place the unit at the strong and stable place.  
A unit placed on an inadequate surface may fall and result in  
injury or equipment damage.If the unit falls, disconnect the power  
immediately and ask your dealer for advice. Do not continue using  
a damaged unit. Using a damaged unit may result in fire or  
electric shock.  
OK  
Set the unit in an appropriate location.  
Not doing so may result in fire, electric shock, or equipment damage.  
z Do not place outdoors.  
z Do not place in the transportation system (ship, aircraft, trains,  
automobiles, etc.)  
z Do not place in a dusty or humid environment.  
z Do not place in a location where the steam comes directly on  
the screen.  
z Do not place near heat generating devices or a humidifier.  
To avoid danger of suffocation, keep the plastic packing  
bags away from babies and children.  
Use the enclosed power cord and connect to the standard  
power outlet of your country.  
Be sure to remain within the rated voltage of the power cord.Not  
doing so may result in fire or electric shock.  
To disconnect the power cord, grasp the plug firmly and pull.  
OK  
Tugging on the cord may damage and result in fire or electric shock.  
PRECAUTIONS 5  
English  
WARNING  
The equipment must be connected to a grounded main outlet.  
Not doing so may cause in fire or electric shock.  
Use the correct voltage.  
z The unit is designed for use with a specific voltage only.  
Connection to another voltage than specified in this User’s  
Manual may cause fire, electric shock, or equipment damage.  
z Do not overload your power circuit, as this may result in fire or  
electric shock.  
Handle the power cord with care.  
z Do not place the cord underneath the unit or other heavy objects.  
z Do not pull on or tie the cord.  
If the power cord becomes damaged, stop using it. Use of a  
damaged cord may result in fire or electric shock.  
Never touch the plug and power cord if it begins to thunder.  
Touching them may result in electric shock.  
When attaching an arm stand, please refer to the user’s  
manual of the arm stand and install the unit securely with  
the enclosed screws.  
Not doing so may cause the unit to come unattached, which may  
result in injury or equipment damage. When the unit is dropped,  
please ask your dealer for advice. Do not continue using a  
damaged unit. Using a damaged unit may result in fire or electric  
shock. When reattaching the tilt stand, please use the same screws  
and tighten them securely.  
Do not touch a damaged LCD panel directly with bare hands.  
The liquid crystal which leaks from the panel is poisonous if it  
enters the eyes or mouth. If any part of the skin or body comes in  
direct contact with the panel, please wash thoroughly. If some  
physical symptoms result, please consult your doctor.  
Follow local regulation or laws for safe disposal.  
The backlight of the LCD panel contains mercury.  
6 PRECAUTIONS  
English  
CAUTION  
Handle with care when carrying the unit.  
Disconnect the power cord and cables when moving the unit.  
Moving the unit with the cord attached is dangerous. It may  
result in injury.  
When handling the unit, grip the bottom of the unit firmly  
with both hands ensuring the panel faces outward before  
lifting.  
OK  
Dropping the unit may result in injury or equipment damage.  
Do not block the ventilation slots on the cabinet.  
z Do not place any objects on the ventilation slots.  
z Do not install the unit in a closed space.  
z Do not use the unit laid down or upside down.  
Blocking the ventilation slots prevents proper airflow and may  
result in fire, electric shock, or equipment damage.  
Do not touch the plug with wet hands.  
Doing so may result in electrical shock.  
Use an easily accessible power outlet.  
This will ensure that you can disconnect the power quickly in case  
of a problem.  
Periodically clean the area around the plug.  
Dust, water, or oil on the plug may result in fire.  
Unplug the unit before cleaning it.  
Cleaning the unit while it is plugged into a power outlet may result  
in electric shock.  
If you plan to leave the unit unused for an extended period,  
disconnect the power cord from the wall socket after turning  
off the power switch for the safety and the power  
conservation.  
PRECAUTIONS 7  
English  
LCD Panel  
When the monitor is cold and brought into a room or the room  
temperature goes up quickly, dew condensation may occur inside  
and outside the monitor. In that case, do not turn the monitor on  
and wait until dew condensation disappears, otherwise it may  
cause some damages to it.  
In order to suppress the luminosity change by long-term use and to  
maintain the stable luminosity, use of a monitor in lower  
brightness is recommended.  
The screen may have defective pixels. These pixels may appear as  
slightly light or dark area on the screen. This is due to the  
characteristics of the panel itself, and not the product.  
The backlight of the LCD panel has a fixed life span. When the  
screen becomes dark or begins to flicker, please contact your  
dealer.  
Do not press on the panel or edge of the frame strongly, as this  
may result in damage to the screen. There will be prints left on the  
screen if the pressed image is dark or black. If pressure is  
repeatedly applied to the screen, it may deteriorate or damage  
your LCD panel. Leave the screen white to decrease the prints.  
Do not scratch or press on the panel with any sharp objects, such  
as a pencil or pen as this may result in damage to the panel. Do  
not attempt to brush with tissues as this may scratch the LCD  
panel.  
When the screen image is changed after displaying the same image  
for extended periods of time, an afterimage may appear. Use the  
screen saver or timer to avoid displaying the same image for  
extended periods of time.  
8 PRECAUTIONS  
English  
1. INTRODUCTION  
Thank you very much for choosing an EIZO Color Monitor.  
1-1. Features  
z Dual inputs compliant  
z DVI Digital input (TMDS) compliant  
z [Horizontal scanning frequency] Analog: 24.8 - 80 kHz  
Digital: 31 - 64 kHz  
[Vertical scanning frequency]  
Analog: 50 - 75 Hz  
Digital: 59 - 61 Hz (VGA text: 69 - 71 Hz)  
1280 dots x 1024 lines  
[Resolution]  
z Auto Adjustment compliant  
z FineContrast modes, to select the most suitable mode for screen display  
z The EIZO LCD Utility Disk enclosed (See readme.txt in the CD-ROM for details.)  
The utility software “ScreenManager Pro for LCD” (for Windows) to control a  
monitor form a PC with a mouse and a keyboard  
The software “DesktopViewer” (for Windows) to display bright and clear still  
images  
z The height adjustable stand incorporated  
z Support to sRGB standard  
1-2. Package Contents  
Please contact your local dealer for assistance if any of the listed items are missing or  
damaged.  
z LCD Monitor  
z User’s Manual (in the CD-ROM)  
z Setup Guide  
z Power Cord  
z Signal Cable (MD-C87)  
z Signal Cable (FD-C35/FD-C39)  
z EIZO USB Cable (MD-C93)  
z EIZO LCD Utility Disk  
z ScreenManager Quick Reference  
z LIMITED WARRANTY  
z Mounting Screws: M4 x 12 (mm) x 4 pcs  
NOTE  
z Please retain the packing materials for future transference.  
z The EIZO USB cable is used when using the software in the EIZO Utility Disk. For  
information on the software, refer to the readme.txt in the EIZO LCD Utility Disk.  
1. INTRODUCTION 9  
     
English  
1-3. Controls & Connectors  
Front (L768 is given as an example)  
(1)  
FineContrast Menu  
Control Panel  
(2) (3) (4) (5)  
(6)  
(7) (8)  
(1) ScreenManager®  
(2) Input Signal Selection Button  
(4) Auto Adjustment Button  
(5) Enter Button  
(6) Control Buttons (Left, Down, Up, Right)  
(7) Power Button  
Blue  
Operation  
Yellow  
Power saving  
Flashing yellow (2 times for each)  
Off  
Power save mode Digital only  
Power off  
*1 Directly pushing the Mode button allows you to select a FineContrast mode. (The main  
menu of ScreenManager and the FineContrast menu cannot be displayed at the same time.)  
*2 Regarding the power indicator for the “Off Timer”.  
10 1. INTRODUCTION  
     
English  
Rear (L768 is given as an example)  
(10)  
(9)  
Bottom  
(12)  
(13) (14)  
(11)  
(9) Security Lock Slot*3  
(10) Stand (Detachable)*4  
(11) Power Connector  
(12) DVI-D Input Connector  
(13) D-Sub mini 15 pin Input Connector  
(14) USB Port (1 Upstream)*5  
*3 Allows for connection of a security cable. This lock supports Kensington’s MicroSaver  
security system. For further information, please consult:  
Kensington Technology Group  
2855 Campus Drive, San Mateo, CA 94403 USA  
Tel.: 800-650-4242, x3348, Intl: 650-572-2700, x3348  
Fax: 650-572-9675  
*4 The LCD monitor can be used with an optional arm stand by removing the stand (see  
*5 USB Port upstream is used when using the software EIZO LCD Utility Disk (p. 15).  
1. INTRODUCTION 11  
 
English  
2. CABLE CONNECTION  
2-1. Before Connecting  
Before connecting your monitor to the PC, change the display screen settings  
(resolution and frequency) in accordance with the charts below.  
NOTE  
z The lower display modes like 640x 480, automatically enlarge to the maximum  
display mode (1280 x 1024), and some lines of the characters may become  
fuzzy. In this case, use <Smoothing> (p. 24) function to make the lines clear.  
z When your computer and display support VESA DDC, the suitable resolution and  
the refresh rate are set by just plugging your display into the computer without  
any manual settings.  
Analog Input  
Resolution  
Frequency  
70 Hz  
Dot Clock  
Remarks  
VGA Graphic  
VGA, VESA  
Apple Macintosh  
VGA TEXT  
VESA  
320  
×
×
×
×
×
×
×
×
×
×
×
×
200  
640  
640  
480  
480  
400  
600  
624  
768  
864  
870  
960  
960  
1024  
~ 75 Hz  
67 Hz  
720  
70 Hz  
800  
~ 75 Hz  
75 Hz  
832  
Apple Macintosh  
VESA  
135 MHz (Max.)  
1024  
1152  
1152  
1280  
1280  
1280  
~ 75 Hz  
75 Hz  
VESA  
75 Hz  
Apple Macintosh  
VESA  
60 Hz  
75 Hz  
Apple Macintosh  
VESA  
~ 75 Hz  
Digital Input  
The monitor supports the following resolutions only.  
Resolution  
Frequency  
60Hz  
Dot Clock  
Remarks  
VGA  
640  
×
×
×
×
×
×
480  
720  
720  
400  
480  
70Hz  
VGA TEXT  
VESA Safe Mode  
VESA  
60Hz  
108 MHz (Max.)  
800  
600  
60Hz  
1024  
1280  
768  
60Hz  
VESA  
1024  
60Hz  
VESA  
12 2. CABLE CONNECTION  
   
English  
2-2. Connecting the Signal Cable  
NOTE  
z Be sure that the power switches of both the PC and the monitor are OFF.  
1. Plug the signal cable into the connector at the rear of the monitor  
and the other end of the cable into the video connector on the PC.  
After connecting, secure the connection with the screw-in fasteners.  
Analog Input  
Power Cord  
Signal Cable  
Connector of the PC  
PC  
Signal Cable (enclosed)  
Video Output Connector /  
D-Sub mini 15 pin  
z
z
Standard graphics card  
Power Macintosh G3  
(Blue & White) / Power  
Mac G4 (VGA)  
Signal Cable (enclosed) +  
Macintosh Adapter (Optional)  
Video Output Connector /  
D-Sub 15 pin  
z
Macintosh  
2. CABLE CONNECTION 13  
 
English  
Digital Input  
Power Cord  
Signal Cable  
Connector of the PC  
PC  
FD-C35 / FD-C39 (enclosed)  
Video Output Connector /  
DVI  
z
z
Digital Graphics card  
Power Mac G4/G5 (DVI)  
NOTE  
z The monitor is not compatible with a Power Mac G4/G5 ADC (Apple Display  
Connector).  
2. Plug the power cord into the power connector on the rear of the  
monitor. Then, plug the other end of the cord into a power outlet.  
WARNING  
Use the enclosed power cord and connect to the  
standard power outlet of your country.  
Be sure to remain within the rated voltage of the power  
cord. Not doing so may result in fire or electric shock.  
The equipment must be connected to a grounded main  
outlet.  
Not doing so may result in fire or electric shock.  
14 2. CABLE CONNECTION  
English  
3. Adjust the “height”, “front and back position” and “angle” of the  
monitor (L768-AS only).  
Move Slowly  
Grip both side of the center part of the  
monitor and move slowly (refer to the  
right figure.)  
Both Side of Center  
Part of the Monitor  
(1) Adjust the height of the monitor. To  
heighten, push the monitor backward. To lower, pull the monitor forward.  
(2) Adjust the position and angle of the monitor.  
(3) If necessary, fine adjust the height of the monitor.  
4. Turn on the monitor’s main power and then switch on the PC’s  
power.  
The monitor’s power indicator will light up (blue). If an image does not appear,  
refer to the “6. TROUBLESHOOTING” for advice. Whenever finished, turn  
off the PC and the monitor.  
5. When using the software in the EIZO LCD Utility Disk: Connect  
the upstream port of the monitor to the downstream port of the  
USB compliant PC or another hub with the USB cable.  
After connecting the USB cable, the USB function can be set up automatically.  
For further details about the software, refer to the readme.txt in the CD-ROM.  
NOTE  
z Adjust brightness of the screen depending on the brightness of your  
environment. Too dark or too bright of a screen can cause eyestrain.  
z Be sure to take adequate rests. A 10-minute rest period each hour is  
suggested.  
2-3. Connecting Two PCs to the Monitor  
Two PCs can be connected to the monitor through the DVI and the D-Sub mini 15 pin  
connector on the back of the monitor.  
Selecting the Active Input  
The Input signal selection button on the control panel can be used to select either DVI  
or D-Sub as the active input at any time. Every time the button is pressed, the input  
changes. When switching the signal, the kind of the input signal (Analog or Digital) is  
displayed for a few seconds on the right top corner of the screen.  
Input Signal Selection Button  
2. CABLE CONNECTION 15  
   
English  
3. SCREENMANAGER  
3-1. How to use the ScreenManager  
ScreenManager allows you to adjust screen performance though the main menu and  
select a FineContrast mode easily.  
[Ex.] Custom  
Main Menu  
Control Buttons  
Left, Down, Up, Right  
FineContrast Menu  
Enter Button  
Auto Adjustment Button  
Mode Button  
NOTE  
z Main Menu and FineContrast Menu cannot be activated at the same time.  
1. Entering the ScreenManager  
Press the Enter Button once to display the main menu of the ScreenManager.  
2. Making Adjustments and Settings  
(1) Select the desired sub menu icon using the Control buttons and press the  
Enter button. The sub menu appears.  
(2) Use the Control buttons to select the desired setting icon and press the  
Enter button. The setting menu appears.  
(3) Use the Control buttons to make all required adjustments and press the  
Enter button to save the settings.  
3. Exiting the ScreenManager  
(1) To return to the main menu, select the <Return> icon or press the Down  
button twice, followed by the Enter button.  
(2) To exit the ScreenManager, select <Exit> icon or press the Down button  
twice, followed by the Enter button.  
NOTE  
z Double clicking the Enter button also exits the ScreenManager menu.  
Directly pressing the Mode button allows you to select the best suited  
mode for screen display from 5 FineContrast modes; Custom, sRGB,  
Text, Picture and Movie. To exit the menu, press the Enter button.  
16 3. SCREENMANAGER  
   
English  
3-2. ScreenManager Adjustments and Settings.  
The following table shows all the ScreenManager’s adjustment and setting menus.  
“*” indicates adjustments of analog input only and “**” indicates digital input only.  
Main menu  
Screen  
Sub menu  
Reference  
Clock  
*
*
*
*
Phase  
Position  
Range Adjustment  
Smoothing  
Brightness  
Temperature  
Gamma  
Color  
1
(Custom)*  
Saturation  
Hue  
Gain  
Reset  
Power Manager DVI DMPM  
VESA DPMS  
*
Others  
Input Signal  
Set the input signal selection of  
automatic or manual (p. 20).  
Off Timer  
Set the monitor’s off timer.  
VGA Selection  
Menu Position  
Translucent  
Menu Off Timer  
Reset  
*
Select the display mode (p. 31).  
Adjust the menu position  
Set the transparency of the menu.  
2
Set the menu displaying time.*  
Return to the factory default settings.  
Information  
Language  
Information  
Review the ScreenManager’s settings,  
model name, serial number and usage  
time.*  
English, German, French,  
Spanish, Italian, Swedish  
and Japanese  
Select the ScreenManager’s language.  
*1 The adjustable functions on the <Color> menu depend on the selected FineContrast mode.  
The above table shows the sub menus when the “Custom” mode is selected (see “4-2. Color  
*2 The displaying time of the FineContrast Menu cannot be changed.  
*3 Due to the inspection on the factory, the usage time may not “0 hour” at shipping.  
3. SCREENMANAGER 17  
   
English  
3-3. FineContrast  
This function allows you to select the best suited mode for screen display.  
To select the Mode  
Directly pressing the Mode button allows you to select the best suited mode for screen  
display from 5 FineContrast modes; Custom, sRGB, Text, Picture and Movie.  
Exit  
press the Enter button to exit the menu. Leaving the Mode button untouched more  
than 5 seconds also exits the menu.  
FineContrastMenu  
Ex.) Custom  
Current  
Mode  
Enter Button  
Mode Button  
FineContrast Mode  
Selectable FineContrast modes are as follows.  
Custom  
sRGB  
To adjust the color settings according to your preference  
To display the screen images based on those original colors (ex. over the  
Internet)  
Text  
Text on word processor or spreadsheet software  
Photo or picture image  
Picture  
Movie  
Animated images  
Color Adjustment of the Mode Settings  
The color settings of each mode can be adjusted by using the <Color> menu of the  
ScreenManager. (See “4-2. Color Adjustment”.)  
18 3. SCREENMANAGER  
   
English  
3-4. Useful Functions  
Adjustment Lock  
Use the “Adjustment Lock” function to prevent any accidental changes.  
Locked function  
z
z
Settings in the ScreenManager  
Auto adjustment button adjustments  
Unlocked function  
z
z
z
z
Selecting of the FineContrast mode by the Mode button.  
Brightness adjustment by Control buttons  
Input signal selection button  
Turning the power on and off by the Power button  
[How To lock]  
(1) Switch off the monitor’s power by the power button on the control panel.  
(2) Press on the Auto adjustment button while switching on the monitor’s power.  
[How To unlock]  
(1) Switch off the monitor’s power by the power button on the control panel.  
(2) Hold down the Auto adjustment button once again and turn the power back on.  
Off Timer  
The off timer function causes the monitor to automatically enter a power off state  
after a predetermined amount of time has lapsed. This function was created to reduce  
afterimage characteristics that are particular to LCD monitors when the monitor  
screen is left on for a long period without use.  
[Procedure]  
(1) Select <Off Timer> in the ScreenManager <Others> menu.  
(2) Select “Enable” and press the Right and Left buttons to adjust the “On Period”  
(1 to 23 hours).  
[Off Timer System]  
PC  
Monitor  
Power Indicator  
On Period (1H - 23H)  
Last 15 min. in “On period”  
“On period” expired  
Operation  
Blue  
1
Advance Notice*  
Power Off  
Blue Flashing  
Off  
*1 Advance notice (Power Indicator flashing blue) will be given 15 minutes before the monitor  
automatically enters the “Power Off” mode. To delay entering the “Power Off” mode,  
press the power button during the advance notice period. The monitor will continue to  
operate for an additional 90 minutes.  
3. SCREENMANAGER 19  
       
English  
[Power Resumption Procedure]  
Press the Power button.  
NOTE  
z The off timer function works while the PowerManager is active, but there is no  
advance notice before the monitor’s power is switched off.  
EIZO Logo Disappearing Function  
When switching on the power button on the front panel, the EIZO logo is displyed  
for a while. If you desire to display or undisplay this logo, use this function. (Default  
is logo appearing.)  
[To undisplay]  
Switch off the monitor’s power by the power button, then hold down the Enter  
button once again and turn the power back on.  
[To display]  
Switch off the monitor’s power by the power button, then hold down the Enter  
button once again and turn the power back on.  
Automatically Selecting the Input Signal Function  
The monitor will automatically detect the inputted signal of either the connection for  
display. (Default: this function is set (“Auto”).)  
NOTE  
z Connecting Two PCs to the Monitor  
When the one computer is switched off or entering the power saving mode, the  
monitor will automatically display the other signal.  
Use the ScreenManager to switch the input selection to manual.  
[Procedure]  
(1) Select <Input Signal> in the <Others> menu.  
(2) Select <Manual>.  
20 3. SCREENMANAGER  
 
English  
4. ADJUSTMENT  
The monitor displays the digital input image correctly based on its pre-  
setting data.  
4-1. Screen Adjustment  
Screen adjustments for the LCD monitor should be used in suppressing screen  
flickering and also for adjusting the screen to its proper position. There is only one  
correct position for each display mode. It is also recommended to use the  
ScreenManager function when first installing the display or whenever changing the  
system. For convenience, an easy set-up Program installed on the utility disk to assist  
in the set-up procedure is provided.  
NOTE  
z Allow the LCD monitor to stabilize for at least 20 minutes before making image  
adjustments.  
Adjustment Procedure  
1. Press the Auto adjustment button on the front panel.  
The message “Your setting will be lost, if you press again now.” appears and  
remains on the screen for 5 seconds. While the message is on the screen, press  
the Auto adjustment button again to automatically adjust the clock, phase,  
screen position and resolution. If you do not wish to do adjust the screen, do  
not press the Auto adjustment button again.  
NOTE  
z The Auto sizing function is intended for use on the Macintosh and on AT-  
compatible PC running Windows. It may not work properly in either of the  
following cases.When running an AT-compatible PC on MS-DOS (Not  
windows). The background color for the “wall paper” or “desktop” pattern is  
set to black.  
If the appropriate screen cannot be made by using the Auto  
adjustment button, adjust the screen through the following  
procedures. If the appropriate screen can be made, proceed to step 4.  
4. ADJUSTMENT 21  
     
English  
2. Run the “Screen adjustment program”.  
Having read the “Readme.txt” file, run the “Screen adjustment program” in the  
enclosed EIZO LCD Utility Disk. Step by step, adjustment is provided by the  
wizard guide.  
NOTE  
z If the user’s operating system has no utility disk (e.g. OS/2), we  
recommend setting the desktop pattern to that as shown in the diagram on  
the following.  
3. Adjust by using <Screen> menu in the ScreenManager.  
(1) Vertical bars appear on the screen  
Use the <Clock> adjustment.  
Select the <Clock> and eliminate the vertical bars by using the Right and  
Left of the Control buttons.  
Do not continuously press the Control buttons, as the adjustment value  
will change quickly and make it difficult to locate the most suitable  
adjustment point. If the horizontal flickering, blur or bars appear, proceed  
to <Phase> adjustment as follows.  
22 4. ADJUSTMENT  
 
English  
(2) Horizontal bars appear on the screen.  
Use the <Phase> (p. 38) adjustment.  
Select the <Phase> and eliminate the horizontal flickering, blurring or  
bars by using the Right and Left buttons.  
NOTE  
z Horizontal bars may not completely disappear from the screen  
depending on the PC.  
(3) The screen position is incorrect.  
Use the <Position> adjustment.  
The correct displayed position of the monitor is decided because the  
number and the position of the pixels are fixed. The <Position>  
adjustment moves the image to the correct position.  
Select <Position> and adjust the position by using the Up, Down, Right  
and Left buttons.  
If vertical bars of distortion appear after finishing the <Position>  
adjustment, return to <Clock> adjustment and repeat the previously  
explained adjustment procedure. Clock Phase Position.  
4. Adjust the output signal range (Dynamic Range) of the signal.  
Use the <Range Adjustment> of <Screen> menu.  
This controls the level of output signal range to display the whole color  
gradation (256 colors).  
[Procedure]  
Press the Auto adjustment button on the front panel while displaying the  
<Range Adjustment> menu to automatically adjust the range. The screen blanks  
for a moment and adjusts the color range to display the whole color gradation  
of the current output signal.  
4. ADJUSTMENT 23  
     
English  
5. To smooth the blurred texts of the enlarged screen of the lower  
resolutions.  
Switch the <Smoothing> setting.  
Select the suitable level from 1 - 5 (Soft - Sharp).  
Select <Smoothing> in the <Screen> menu and adjust by using the Right and  
Left buttons.  
NOTE  
z The <Smoothing> is disabled in the resolution 1280 x 1024.  
z Since the displayed image is enlarged, the blurred texts may not be  
necessarily lost completely.  
24 4. ADJUSTMENT  
 
English  
4-2. Color Adjustment  
Color settings of each FineContrast mode can be adjusted and saved by using the  
<Color> menu of the ScreenManager.  
In the analog input, perform the <Range Adjustment> (p. 23) before making  
the color adjustments.  
Adjustment Items  
The adjustable items and displayed icons on the <Color> menu depend on the selected  
FineContrast mode.  
”: Settable/Adjustable “–”: Fixed at the factory  
FineContrast Modes  
Icons  
Functions  
Custom  
sRGB  
Text  
Picture  
Movie  
Brightness  
Temperature  
Gamma  
Saturation  
Hue  
Gain  
Reset  
NOTE  
z Allow the LCD monitor to stabilize for at least 20 minutes before making image  
adjustments.  
z Performing the <Reset> of the <Color> menu returns the color settings of the  
selected mode to the default settings.  
4. ADJUSTMENT 25  
   
English  
0
Menu  
Function Descriptions  
Adjustable range  
Brightness  
To set the brightness of the  
screen  
0 ~ 100 %  
Temperature To set the color temperature  
4,000 ~ 10,000 K  
in 500 K increments (including 9,300 K).  
Default setting is off (normal white)  
NOTE  
z
The values shown in the Kelvin are available only as a reference tool.  
z
Setting the temperature under 4,000 K or over 10,000 K invalidates the  
color temperature setting. (The color temperature’s setting turns “OFF”.)  
To set the gamma value  
1.8 ~ 2.6 (in 0.2 increments)  
NOTE  
z
If setting the gamma value, the using the monitor in the digital signal  
input is recommended.  
Saturation  
To change the saturation  
-128 ~ 127  
Setting the minimum level (-128) turns the  
image to the monochrome.  
NOTE  
z
The <Saturation> adjustment may cause undisplayable color tone.  
Hue  
To change the flesh color, etc. -32 ~ 32  
NOTE  
z
The <Hue> adjustment may cause undisplayable color tone.  
Gain  
To change each color  
(red, green and blue)  
0 ~ 100%  
By adjusting the red, green and blue color  
tones for each mode, custom colors can be  
defined. Display a white or gray  
background image and adjust the <Gain>.  
NOTE  
z
The values shown in the percentage are available only as a reference tool.  
z
Setting the <Temperature> invalidates the <Gain> adjustment. <Gain>  
setting returns to the defaul.  
Reset  
To return the color settings of Select the <Reset>.  
the selected mode to the  
default settings  
26 4. ADJUSTMENT  
English  
4-3. Power-save Setup  
The <PowerManager> menu in the ScreenManager enables to set the power-save setup.  
NOTE  
z Do your part to conserve energy, turn off the monitor when you are finished using  
it. Disconnecting the monitor from the power supply is recommended to save  
energy completely.  
Analog Input  
This monitor complies with the “VESA DPMS”.  
[Procedure]  
(1) Set the PC’s power saving settings.  
(2) Select “VESA DPMS” from the <PowerManager> menu.  
[Operation]  
PC  
Monitor  
Power Indicator  
Operation  
Operation  
Blue  
Power saving  
STAND-BY  
Power saving  
Yellow  
SUSPEND OFF  
[Power Resumption Procedure]  
Operate the mouse or keyboard to return to a normal screen.  
Digital Input  
This monitor complies with the “DVI DMPM”.  
[Procedure]  
(1) Set the PC’s power saving settings.  
(2) Select “DVI DMPM” from the <PowerManager> menu.  
[Power Saving System]  
PC  
Monitor  
Operation  
Power Indicator  
Blue  
Operation  
Power saving  
Off mode  
Power saving  
Yellow  
Flashing yellow  
(2 times for each)  
1
Power saving*  
*1 Power saving through the PC’s off mode is only supported when “Manual” is selected on  
the ScreenManager’s <Input Signal>.  
4. ADJUSTMENT 27  
   
English  
[Power Resumption Procedure]  
Operate the mouse or keyboard to return to a normal screen from the Power save  
mode of the PC.  
Power on the PC to return a normal screen from the Off mode of the PC.  
28 4. ADJUSTMENT  
 
English  
5. ATTACHING AN ARM STAND  
The LCD monitor can be used with an arm stand by removing the tilt stand and  
attaching the arm stand to the LCD monitor. Using our optional arm or stand is  
recommended. (Ask your local dealer for information.)  
NOTE  
z If you will use the arm or stand of other companies, confirm the followings to the  
arm or stand maker before selecting.  
Hole spacing on the arm mounting: 100 mm x 100 mm (VESA compliant)  
Supportable Weight: Total weight of the monitor (without stand) and attaching  
equipment such as a cable  
TÜV/GS approved arm or stand  
z Please connect cables after attaching an arm stand.  
Setup Procedure  
1. Lay the LCD monitor down. Do not scratch the panel.  
2. Remove the tilt stand by loosening the screws  
(4 pcs of M4 x 14 mm).  
3. Attach an arm stand to the LCD monitor securely.  
Arm-stand  
4 Mounting Screws : M4 x 12 mm (Enclosed)  
5. ATTACHING AN ARM STAND 29  
   
English  
6. TROUBLESHOOTING  
If a problem persists even after applying the suggested remedies, contact an EIZO dealer.  
z No picture problems See No.1 ~ No.2  
z Imaging problems See No.3 ~ No.11  
z Other problems See No.12 ~ No.14  
Problems  
1. No picture  
Points to check with Possible Solutions  
Check that the power cord is correctly  
connected. If the problem persists, turn off the  
monitor power for a few minutes, then turn it  
back on and try again.  
z
Indicator status: Off  
z
Indicator status: Blue  
Check the “Brightness” setting.  
Switch the signal input by pressing the Input  
Signal Selection Button on the front control  
panel.  
z
z
Indicator status: Yellow  
Try pressing a key on the keyboard, or clicking  
the mouse.  
Indicator status: Flashing  
Yellow (twice for each)  
Try pressing the power of the computer (p. 28).  
2. Following messages appear.  
(Error messages shown below  
will remain on the screen for 40  
seconds.)  
These messages appear when the signal is not  
inputted correctly, even if the monitor functions  
properly.  
When the image is displayed correctly after a  
short time, there is no problem with the monitor.  
(Some PCs do not output the signal soon after  
powering on.)  
Check that the signal cable is properly  
connected to the PC or graphics board.  
Switch the signal input by pressing the Input  
signal selection button on the front control panel.  
z
Whenever an error signal  
message appears, the  
signal frequency will be  
displayed in red.  
Use the graphics board’s utility software to  
change the frequency setting. (Refer to the  
manual of the graphics board.)  
(Example)  
30 6. TROUBLESHOOTING  
   
English  
Problems  
Points to check with Possible Solutions  
3. Display position is incorrect.  
Adjust the image position using the <Position>  
The two display modes, VGA 720 x 400 (70 Hz)  
and 320 x 200 (70 Hz), have the same signal  
timings. Using <VGA Selection> selects the  
appropriate display mode. (This function effects  
only when the resolution is VGA 720 x 400 (70  
Hz) or 320 x 200 (70 Hz).  
If the problem persists, use the graphics  
board’s utility software to change the display  
position if available.  
4. Vertical bars of distortion appear.  
Decrease the vertical bars using the <Clock>  
5. Horizontal bars of distortion  
appear.  
Decrease the horizontal bars using the  
<Phase> (p. 23).  
6. Letters and lines appear blurred.  
Switch the <Smoothing> (p. 24) mode to “Off”.  
7. The screen is too bright or too  
dark.  
Adjust the <Brightness> (The backlight of the  
LCD monitor has a fixed life span. When the  
screen becomes dark or begins to flicker,  
please contact your dealer.)  
8. Afterimages appear.  
Do you use the screen saver or timer when  
displaying the same image for extended  
periods of time?  
Afterimages are particular to LCD monitors.  
Avoid displaying the same image for extended  
periods of time.  
9. The screen has defective pixels  
(e.g. slightly light or dark).  
This is due to the characteristics of the panel  
itself, and not the LCD product.  
10. Fingerprints remain on the  
screen.  
Leaving the screen white may solve the  
problem.  
11. The <Smoothing> cannot be  
selected.  
<Smoothing> is disabled when the screen is  
displayed in the 1280 x1024.  
6. TROUBLESHOOTING 31  
 
English  
Problems  
Points to check with Possible Solutions  
12. The ScreenManager cannot be  
activated.  
The adjustment lock is probably on.  
To unlock (p. 19): switch the LCD monitor off.  
Then, while pressing the Auto adjustment  
button switch, the power on.  
13. The Auto Adjustment Button  
does not operate.  
The Auto adjustment button does not operate  
when the digital signal is inputted  
The adjustment lock is probably on.  
To unlock (p. 19): switch the monitor off. Then,  
while pressing the Auto adjustment button,  
switch the monitor on.  
14. The Input signal selection button  
does not operate.  
The computer with digital may be in the off  
mode (power indicator flashing yellow). Try to  
press the monitor’s power button and press the  
Input signal selection button again.  
32 6. TROUBLESHOOTING  
English  
7. CLEANING  
Periodic cleaning is recommended to keep the monitor looking new and to prolong its  
operation lifetime.  
NOTE  
z Never use thinner, benzene, alcohol (ethanol, methanol, or isopropyl alcohol),  
abrasive cleaners, or other strong solvents, as these may cause damage to the  
cabinet or LCD panel.  
Cabinet  
To remove stains, wipe the cabinet with a soft, lightly moistened cloth using a mild  
detergent. Do not spray wax or cleaner directly into the cabinet. (For details, refer to  
the manual of the PC.)  
LCD Panel  
z The LCD surface can be cleaned with a soft cloth, such as cotton or lens paper.  
z If necessary, stubborn stains can be removed by moistening part of a cloth with  
water to enhance its cleaning power.  
7. CLEANING 33  
 
English  
8. SPECIFICATIONS  
LCD Panel  
48 cm (19.0 inch), TFT color LCD panel with Anti-Glare  
Hard Coating, Viewing Angle: H: 178°, V: 178° (CR 10)  
Dot Pitch  
0.294 mm  
Horizontal Scan Frequency  
Analog: 24.8 ~ 80 kHz (Automatic)  
Digital: 31 ~ 64 kHz  
Vertical Scan Frequency  
Analog: 50 ~ 75 Hz (Automatic)  
Digital: 59 ~ 61 Hz, (VGA Text: 69 ~ 71 Hz)  
Resolution  
1280 dots x 1024 lines  
Dot Clock (Max.)  
Display Colors  
Display Area  
Analog: 135 MHz, Digital: 108 MHz  
16 million colors (max)  
376 mm (H) x 301 mm (V) (14.8” (H) x 11.9” (V))  
(Viewable image size: 481 mm (19.0”))  
Power Supply  
100 - 120 VAC 10%, 50/60 Hz, 0.7 A  
200 - 240 VAC 0%, 50 Hz, 0.4 A  
Power Consumption  
Max.: 40 W  
Power Saving Mode: Less than 2 W (for single signal input)  
Input Connector  
D-Sub mini 15 pin, DVI-D  
Separate, TTL, Positive/Negative  
0.7 Vp-p / 75 Positive  
TMDS (Single Link)  
Analog Input Signal (Sync)  
Analog Input Signal (Video)  
Input Signal (Digital)  
Signal registration  
Analog: 45 (Factory preset: 20)  
VESA DDC 2B  
Plug & Play  
Dimensions  
L768  
404 mm (W) x 406 ~ 506 mm (H) x 205 mm (D)  
(15.9” (W) x 16” ~ 19.9” (H) x 8.1” (D))  
L768-AS  
404 mm (W) x 288 ~ 423 mm (H) x 200 mm (D)  
(15.9” (W) x 11.3” ~ 16.7” (H) x 7.9” (D))  
Dimensions (without stand)  
404 mm (W) x 333 mm (H) x 60 mm (D)  
(15.9” (W) x 13.1” (H) x 2.36” (D))  
Weight  
L768  
6.8 kg (15 lbs.)  
L768-AS  
6.6 kg (14.6 lbs.)  
Weight (without stand)  
Temperature  
4.8 kg (10.6 lbs.)  
Operating: 0°C ~ 35°C (32°F ~ 95°F)  
Storage: -20°C ~ 60°C (-4°F ~ 140°F)  
Humidity 30% to 80% R.H. Non-condensing  
34 8. SPECIFICATIONS  
 
English  
Certifications and Standards  
100-120 VAC  
1
2
TCO’03* , TCO’99* , NRTL/C-TÜV, FCC-B, EPA ENERGY  
STAR Program, TÜV/Rheinland Ergonomics Approved  
1
2
200-240 VAC  
TCO’03* , TCO’99* , CE, CB, TÜV Rheinland/GS, EPA  
ENERGY STAR Program, TÜV/Rheinland Ergonomics  
Approved  
*1 Applicable to gray color version only.  
*2 Applicable to black color version only.  
Default settings  
Analog input  
Digital input  
Brightness  
100%  
100%  
Smoothing  
3
FineContrast Mode  
PowerManager  
Input Signal  
Off Timer  
Custom  
VESA DPMS  
DVI DMPM  
Auto  
Disable  
English  
Language  
8. SPECIFICATIONS 35  
 
English  
Dimensions  
mm (inches)  
<L768>  
<L768-AS>  
36 8. SPECIFICATIONS  
English  
Pin Assignment  
D-Sub mini 15 pin connector  
5
4
3
2
1
10  
9
8
7
6
11  
14 13 12  
15  
Pin  
No.  
Pin  
No.  
Pin  
No.  
Signal  
Red video  
Signal  
Signal  
1
2
3
4
5
6
7
Red ground  
Green ground  
Blue ground  
No pin  
11  
12  
13  
14  
15  
Ground Shorted  
Data (SDA)  
H. Sync  
Green video  
Blue video  
Ground  
8
9
V. Sync  
No pin  
10  
Ground Shorted  
Clock (SCL)  
DVI-D Connector  
3
1
9
17  
2
4
12  
20  
6
7
8
5
13  
21  
10 11  
19  
14 15 16  
24  
22 23  
18  
Pin  
No.  
Pin  
No.  
Pin  
No.  
Signal  
Signal  
Signal  
1
2
3
4
5
6
7
8
TMDS Data 2-  
TMDS Data 2+  
9
TMDS Data 1-  
TMDS Data 1+  
17  
18  
TMDS Data 0-  
TMDS Data 0+  
10  
TMDS Data 2/4 Shield 11 TMDS Data 1/3 Shield 19 TMDS Data 0/5 Shield  
NC*  
NC*  
12  
13  
14  
15  
16  
NC*  
NC*  
20  
21  
22  
23  
24  
NC*  
NC*  
DDC Clock (SCL)  
DDC Data (SDA)  
NC  
+5V Power  
Ground (For +5V)  
Hot Plug Detect  
TMDS Clock shield  
TMDS Clock+  
TMDS Clock-  
(*NC: No Connection)  
8. SPECIFICATIONS 37  
English  
9. GLOSSARY  
Clock  
With the analog input signal display, the analog signal is converted to a digital  
signal by the LCD circuitry. To convert the signal correctly, the LCD monitor needs  
to produce the same number clock pulse as the dot clock of the graphics system.  
When the clock pulse is not correctly set, some vertical bars of distortion are  
displayed on the screen.  
DVI  
(Digital Visual Interface)  
A digital flat panel interface. DVI can transmit digital data from the PC directly  
without loss with the signal transition method “TMDS”.There are two kinds of  
DVI connectors. One is DVI-D connector for digital signal input only. The other is  
DVI-I connector for both digital and analog signal inputs.  
DVI DMPM  
(DVI Digital Monitor Power Management)  
The Power management system for the digital interface. The “Monitor ON” status  
(operation mode) and the “Active Off” status (power-saving mode) are  
indispensable for the DVI-DMPM as the monitor’s power mode.  
Gain Adjustment  
Adjusts each color parameter for red, green and blue. The color of the LCD  
monitor is displayed through the color filter of the LCD panel. Red, green and blue  
are the three primary colors. The colors on the monitor are displayed by  
combining these three colors. The color tone can change by adjusting the  
illumination amount passed through each color’s filter.  
Gamma  
Generally, the relationship that the light intensity values of a monitor change  
nonlinearly to the input signal level is called “Gamma Characteristic”. On the  
monitor, low gamma values display the whitish images and high gamma values  
display the high contrast images.  
Phase  
The phase adjustment decides the sampling timing point for converting the analog  
input signal to a digital signal. Adjusting the phase after the clock adjustment will  
produce a clear screen.  
38 9. GLOSSARY  
           
English  
Range Adjustment  
The Range Adjustment controls the level of output signal range to display the  
whole color gradation.  
Resolution  
The LCD panel consists of a fixed number of pixel elements which are illuminated  
to form the screen image. This products’ display panel consists of 1280 horizontal  
pixels and 1024 vertical pixels. At a resolution of 1280 x 1024, all pixels are  
displayed as a full screen.  
sRGB  
(Standard RGB)  
“International Standard for Red, Green, and Blue color space”  
A color space was defined with the aim of the color matching between applications  
and hardware devices, such as monitors, scanners, printers and digital cameras. As  
a standard default space, sRGB allows Internet users to closely match colors.  
Temperature  
Color Temperature is a method to measure the white color tone, generally  
indicated in degrees Kelvin. At high temperatures the white tone appears  
somewhat blue, while at lower temperatures it appears somewhat red. Computer  
monitors generally give best performance at high temperature settings.  
5,000 K: Slightly reddish white.  
6,500 K: Warm-white tone, similar to white paper or daylight.  
9,300 K: Slightly bluish white.  
TMDS  
(Transition Minimized Differential Signaling)  
A signal transition method for the digital interface.  
VESA DPMS  
(Video Electronics Standards Association - Display Power Management Signaling)  
The acronym VESA stands for “Video Electronics Standards Association”, and  
DPMS stands for “Display Power Management Signaling”. DPMS is a  
communication standard that PCs and graphics boards use to implement power  
savings on the monitor side.  
9. GLOSSARY 39  
           
APPENDIX/ANHANG/ANNEXE  
Preset Timing Chart for Analog input  
Timing-Übersichten für Analog Eingang  
Synchronisation des Signaux pour Analog numerique  
Based on the signal diagram shown below 20 factory presets have been registered in  
the monitor’s microprocessor.  
Der integrierte Mikroprozessor des Monitors unterstützt 20 werkseitige  
Standardeinstellungen (siehe hierzu die nachfolgenden Diagramme).  
25 signaux ont été enregistrés en usine dans le microprocesseur du moniteur,  
conformément au diagramme de synchronisation ci-dessous.  
Sync Polarity  
Frequencies  
Dot Clock  
MHz  
Mode  
H
V
fH: kHz  
fV: Hz  
VGA Graphic  
320 × 200  
25.2  
25.2  
28.3  
30.2  
57.3  
100.0  
126.2  
31.5  
31.5  
36.0  
40.0  
50.0  
49.5  
Nega  
Nega  
Nega  
Nega  
Posi  
Posi  
31.5  
31.5  
31.5  
35.0  
49.7  
68.7  
74.8  
37.9  
37.5  
35.2  
37.9  
48.1  
46.9  
70.1  
VGA  
640 × 480  
Nega  
Posi  
60.0  
70.1  
66.7  
74.6  
75.1  
74.8  
72.8  
75.0  
56.3  
60.3  
72.2  
75.0  
VGA Text  
720 × 400  
Macintosh  
640 × 480  
Nega  
Posi  
Macintosh  
832 × 624  
Macintosh  
1152 × 870  
Nega  
Posi  
Nega  
Posi  
Macintosh  
1280 × 960  
VESA  
640 × 480  
Nega  
Nega  
Posi  
Nega  
Nega  
Posi  
VESA  
640 × 480  
VESA  
800 × 600  
VESA  
800 × 600  
Posi  
Posi  
VESA  
800 × 600  
Posi  
Posi  
VESA  
800 × 600  
Posi  
Posi  
APPENDIX/ANHANG/ANNEXE i  
Sync Polarity  
Frequencies  
Dot Clock  
MHz  
Mode  
H
V
fH: kHz  
fV: Hz  
VESA  
1024 × 768  
65.0  
75.0  
Nega  
Nega  
Posi  
Posi  
Posi  
Posi  
Posi  
Nega  
48.4  
56.5  
60.0  
67.5  
60.0  
64.0  
80.0  
60.0  
VESA  
1024 × 768  
Nega  
Posi  
Posi  
Posi  
Posi  
Posi  
70.1  
75.0  
75.0  
60.0  
60.0  
75.0  
VESA  
1024 × 768  
78.8  
VESA  
1152 × 864  
108.0  
108.0  
108.0  
135.0  
VESA  
1280 × 960  
VESA  
1280 × 1024  
VESA  
1280 × 1024  
ii APPENDIX/ANHANG/ANNEXE  
[Applicable to gray cabinet version only.]  
Congratulations!  
The display you have just purchased carries the TCO’03 Displays  
label. This means that your display is designed, manufactured  
and tested according to some of the strictest quality and  
environmental requirements in the world. This makes for a high  
performance product, designed with the user in focus that also  
minimizes the Impact on our natural environment.  
Some of the features of the TCO’03 Display requirements:  
Ergonomics  
z Good visual ergonomics and image quality in order to improve the working  
environment for the user and to reduce sight and strain problems. Important  
parameters are luminance, contrast, resolution, reflectance, colour rendition and  
image stability.  
Energy  
z Energy-saving mode after a certain time - beneficial both for the user and environment  
z Electrical safety  
z Emissions  
Electromagnetic fields  
z Noise emissions  
Ecology  
z The products must be prepared for recycling and the manufacturer must have a  
certified environmental management system such as EMAS or ISO 14000  
z Restrictions on  
 chlorinated and brominated flame retardants and polymers  
 heavy metals such as cadmium, mercury and lead.  
The requirements includes in this label have been developed by TCO Development in co-  
operation with scientists, experts, users as well as manufacturers all over the world. Since the  
end of the 1980s TCO has been involved in influencing the development of IT equipment in a  
more user-friendly direction. Our labeling system with displays in 1992 and is now requested  
by users and IT-manufacturers all over the world.  
For more information, please visit  
[Applicable to black cabinet version only]  
Congratulations!  
You have just purchased a TCO’99 approved and labelled  
product! Your choice has provided you with a product developed  
for professional use. Your purchase has also contributed to  
reducing the burden on the environment and also to the further  
development of environmentally adapted electronics products.  
Why do we have environmentally labelled computers?  
In many countries, environmental labelling has become an established method for encouraging  
the adaptation of goods and services to the environment. The main problem, as far as  
computers and other electronics equipment are concerned, is that environmentally harmful  
substances are used both in the products and during their manufacture. Since it is not so far  
possible to satisfactorily recycle the majority of electronics equipment, most of these potentially  
damaging substances sooner or later enter nature.  
There are also other characteristics of a computer, such as energy consumption levels, that are  
important from the viewpoints of both the work (internal) and natural (external) environments.  
Since all methods of electricity generation have a negative effect on the environment (e.g. acidic  
and climate-influencing emissions, radioactive waste), it is vital to save energy. Electronics  
equipment in offices is often left running continuously and thereby consumes a lot of energy.  
What does labelling involve?  
This product meets the requirements for the TCO’99 scheme which provides for international  
and environmental labelling of personal computers. The labelling scheme was developed as a  
joint effort by the TCO (The Swedish Confederation of Professional Employees), Svenska  
Naturskyddsforeningen (The Swedish Society for Nature Conservation) and Statens  
Energimyndighet (The Swedish National Energy Administration).  
Approval requirements cover a wide range of issues: environment, ergonomics, usability,  
emission of electric and magnetic fields, energy consumption and electrical and fire safety.  
The environmental demands impose restrictions on the presence and use of heavy metals,  
brominated and chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among  
other things. The product must be prepared for recycling and the manufacturer is obliged to  
have an environmental policy which must be adhered to in each country where the company  
implements its operational policy.  
The energy requirements include a demand that the computer and/or display, after a certain  
period of inactivity, shall reduce its power consumption to a lower level in one or more stages.  
The length of time to reactivate the computer shall be reasonable for the user.  
Labelled products must meet strict environmental demands, for example, in respect of the  
reduction of electric and magnetic fields, physical and visual ergonomics and good usability.  
You will find a brief summary of the environmental requirements met by this product on the  
right. The complete environmental criteria document may be ordered from:  
TCO Development  
SE-114 94 Stockholm, Sweden  
Fax: +46 8 782 92 07  
Email (Internet): [email protected]  
Current information regarding TCO’99 approved and labelled products may also be  
Environmental Requirements  
Flame retardants  
Flame retardants are present in printed circuit boards, cables, wires, casings and housings.  
Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in  
a computer casing can consist of flame retardant substances. Most flame retardants contain  
bromine or chloride, and those flame retardants are chemically related to another group of  
environmental toxins, PCBs. Both the flame retardants containing bromine or chloride and  
the PCBs are suspected of giving rise to severe health effects, including reproductive damage  
in fish-eating birds and mammals, due to the bio-accumulative* processes. Flame retardants  
have been found in human blood and researchers fear that disturbances in foetus  
development may occur.  
The relevant TCO’99 demand requires that plastic components weighing more than 25  
grams must not contain flame retardants with organically bound bromine or chlorine. Flame  
retardants are allowed in the printed circuit boards since no substitutes are available.  
Cadmium**  
Cadmium is present in rechargeable batteries and in the colour-generating layers of certain  
computer displays. Cadmium damages the nervous system and is toxic in high doses.  
The relevant TCO’99 requirement states that batteries, the colour-generating layers of  
display screens and the electrical or electronics components must not contain any cadmium.  
Mercury**  
Mercury is sometimes found in batteries, relays and switches. It damages the nervous system  
and is toxic in high doses.  
The relevant TCO’99 requirement states that batteries may not contain any mercury. It also  
demands that mercury is not present in any of the electrical or electronics components  
associated with the labelled unit.  
CFCs (freons)  
The relevant TCO’99 requirement states that neither CFCs nor HCFCs may be used during  
the manufacture and assembly of the product. CFCs (freons) are sometimes used for washing  
printed circuit boards. CFCs break down ozone and thereby damage the ozone layer in the  
stratosphere, causing increased reception on earth of ultraviolet light with e.g. increased risks  
of skin cancer (malignant melanoma) as a consequence.  
Lead**  
Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages  
the nervous system and in higher doses, causes lead poisoning.  
The relevant TCO’99 requirement permits the inclusion of lead since no replacement has yet  
been developed.  
* Bio-accumulative is defined as substances which accumulate within living organisms.  
** Lead, Cadmium and Mercury are haevy metals which are Bio-accumulative.  
For U.S.A, Canada, etc. (rated 100-120 Vac) Only  
FCC Declaration of Conformity  
We, the Responsible Party  
EIZO NANAO TECHNOLOGIES INC.  
5710 Warland Drive, Cypress, CA 90630  
Phone: (562) 431-5011  
declare that the product  
Trade name: EIZO  
Model: FlexScan L768/L768-AS  
is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the  
following two conditions: (1) this device may not cause harmful interference, and (2) this  
device must accept any interference received, including interference that may cause  
undesired operation.  
This equipment has been tested and found to comply with the limits for a Class B digital  
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide  
reasonable protection against harmful interference in a residential installation. This  
equipment generates, uses, and can radiate radio frequency energy and, if not installed and  
used in accordance with the instructions, may cause harmful interference to radio  
communications. However, there is no guarantee that interference will not occur in a  
particular installation. If this equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the equipment off and on, the user  
is encouraged to try to correct the interference by one or more of the following measures.  
* Reorient or relocate the receiving antenna.  
* Increase the separation between the equipment and receiver.  
* Connect the equipment into an outlet on a circuit different from that to which the  
receiver is connected.  
* Consult the dealer or an experienced radio/TV technician for help.  
Changes or modifications not expressly approved by the party responsible for compliance  
could void the user’s authority to operate the equipment.  
Note  
Use the attached specified cable below or EIZO signal cable with this monitor so as to keep  
interference within the limits of a Class B digital device.  
- AC Cord  
- Shielded Signal Cable (enclosed)  
Canadian Notice  
This Class B digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de le classe B est comforme à la norme NMB-003 du Canada.  
Hinweis zur Ergonomie :  
Dieser Monitor erfüllt die Anforderungen an die Ergonomie nach EK1-ITB 2000 mit dem  
Videosignal, 1280 Punkte × 1024 Zeilen, RGB analog, 0,7 Vp-p und mindestens 75,0 Hz  
Bildwiederholfrequenz, non interlaced. Weiterhin wird aus ergonomischen Gründen  
empfohlen, die Grundfarbe Blau nicht auf dunklem Untergrund zu verwenden (schlechte  
Erkennbarkeit, Augenbelastung bei zu geringem Zeichenkontrast.)  
Hinweise zur Auswahl des richtigen Schwenkarms für Ihren Monitor  
Dieser Monitor ist für Bildschirmarbeitsplätze vorgesehen. Wenn nicht der zum  
Standardzubehör gehörige Schwenkarm verwendet wird, muss statt dessen ein geeigneter  
anderer Schwenkarm installiert werden. Bei der Auswahl des Schwenkarms sind die  
nachstehenden Hinweise zu berücksichtigen:  
Der Standfuß muß den nachfolgenden Anforderungen entsprechen:  
a) Der Standfuß muß eine ausreichende mechanische Stabilität zur Aufnahme des  
Gewichtes vom Bildschirmgerät und des spezifizierten Zubehörs besitzen. Das Gewicht  
des Bildschirmgerätes und des Zubehörs sind in der zugehörenden Bedienungsanleitung  
angegeben.  
b) Die Befestigung des Standfusses muß derart erfolgen, daß die oberste Zeile der  
Bildschirmanzeige nicht höher als die Augenhöhe eines Benutzers in sitzender Position  
ist.  
c) Im Fall eines stehenden Benutzers muß die Befestigung des Bildschirmgerätes derart  
erfolgen, daß die Höhe der Bildschirmmitte über dem Boden zwischen 135 – 150 cm  
beträgt.  
d) Der Standfuß muß die Möglichkeit zur Neigung des Bildschirmgerätes besitzen (max.  
vorwärts: 5°, min. nach hinten 5°).  
e) Der Standfuß muß die Möglichkeit zur Drehung des Bildschirmgerätes besitzen (max.  
180°). Der maximale Kraftaufwand dafür muß weniger als 100 N betragen.  
f) Der Standfuß muß in der Stellung verharren, in die er manuell bewegt wurde.  
g) Der Glanzgrad des Standfusses muß weniger als 20 Glanzeinheiten betragen  
(seidenmatt).  
h) Der Standfuß mit Bildschirmgerät muß bei einer Neigung von bis zu 10° aus der  
normalen aufrechten Position kippsicher sein.  
Recycle Auskunft  
Die Rücknahme dieses Produktes nach Nutzungsende übernimmt EIZO in Deutschland  
zusammen mit dem Partner eds-r gmbh rücknahmesysteme. Dort werden die Geräte in ihre  
Bestandteile zerlegt, die dann der Wiederverwertung zugeführt werden. Um einen  
Abholtermin zu vereinbaren und die aktuellen Kosten zu erfahren, benutzen Sie bitte  
folgende Rufnummer: 02153-73 35 00. Weitere Informationen finden Sie auch unter der  
Recycling Information for customers in Switzerland:  
All recycling information is placed in the SWICO’s website.  
Recycling-Information für Kunden in der Schweiz:  
Alle Informationen zum Thema Recycling finden Sie auf der Homepage des  
Brancheverbandes SWICO.  
Renseignements de recyclage pour les clients en Suisse:  
Vous trouvez tous les renseignements pour le sujet de recyclage sur la page WEB de I’UNION  
DE BRAN CHE SWICO.  
Recycling Information for customers in USA:  
All recycling information is placed in the EIZO Nanao Technologies, Inc’s website.  
Återvinnings information för kunder i Sverige:  
All information om återvinning finns på Eizo Nordics hemsida:  
www.eizo.se  

Hanns G Hi221DP User Manual
Grandstream Networks Handy Tone 386 User Manual
Frigidaire 318046807 2 User Manual
Eizo FlexScan MX Series User Manual
CyberResearch GDO 18 User Manual
Cobra Electronics NavOne 2500 User Manual
Cisco Systems IPS4360 User Manual
Canon LV X4 User Manual
Belshaw Brothers 4 Tray User Manual
Avanti Products Dishwasher DWE1802SS User Manual