Dacor Cooktop RR30NIFS User Manual

RR30NS, RR30NFS, RR30NIS, RR30NIFS  
Document # PG05-009  
Revised 05/23/13 Page 1/5  
Renaissance® 30” Wide  
Electric Inductive Range  
PLANNING  
GUIDE  
Model Versions  
Model  
warning  
Configuration  
Handle Type  
Observe all governing codes and ordinances during planning  
and installation. Contact your local building department for  
further information.  
Freestanding,  
(full size side panels)  
Mounted on  
outside of door  
RR30NS[-C]*  
Freestanding,  
(full size side panels)  
Flush handle,  
integrated in door  
RR30NFS[-C]*  
RR30NIS[-C]*  
This appliance must be installed in accordance with the  
accompanying installation instructions.  
Built-in/Slide-in  
(3 1/4” removable side panels)  
Mounted on  
outside of door  
Built-in/Slide-in  
(3 1/4” removable side panels)  
Mounted on  
outside of door  
available Backguards  
RR30NIFS[-C]*  
Part number Description  
Compatibility  
Optional on all models  
* Order -C option for corded wiring configuration, see page 3/5 for details.  
ADRB30E03  
ADRB30E06  
ADRB30E0
3 Inch  
Standard on models RR30NS, RR30NFS  
Optional on models RR30NIS, RR30NIFS  
ptional on all models  
Models Rme equipped from the factory with  
flat staa backguard. A backguard may be  
purcsory. Add an additional 1/16 inch to depth  
dilling a backguard on models RR30NIS and  
Product Dimensions  
All tolerances ±1/16” (±1.6 mm) unless otherwise noted.  
A
B
C
D
panel  
ckguard thickness  
 
d*  
6” (15.2 cm)  
backguard*  
3” (7.6 cm)  
backguard*  
RR30NI[F]S:  
3/8” (9.5 mm)  
thick top trim  
Dimension rr30nS, rr30nFS  
rr30niS, rr30niFS  
46 1/16” (117.0 cm)  
25 5/16” (64.3 cm)  
23 3/16” (58.9 cm)  
A
C
D
46 1/4” (117.5 cm)  
25 1/2” (64.8 cm)  
23 3/8” (59.4 cm)  
External handle  
shown, some models  
have integral handle  
RR30N[F]S:  
full stainless  
steel side panels  
35”  
(88.9 cm)  
to  
37”  
(94.0 cm)  
Dimension  
rr30nS  
rr30niS  
B
27 7/8” (70.8 cm)  
27 11/16” (70.3 cm)  
RR30NI[F]S:  
3” (7.6 cm)  
partial stainless  
steel side panels  
(removable)  
The trim on models RR30NS and RR30NFS are not compatible  
with a raised vent.  
Models RR30NIS and RR30NIFS are compatible with Dacor  
raised vent models ERV30 and ERV3015. Use only these  
specified raised vent models.  
Product width:  
29 15/16” (76.0 cm)  
*�  
See table for compatibility  
OvERALL DEPth DImENSIONS - SIDE vIEW  
All specifications subject to change without notice.  
Phone: (800) 793-0093  
RR30NS, RR30NFS, RR30NIS, RR30NIFS  
Document # PG05-009  
Revised 05/23/13 Page 3/5  
Renaissance 30” Wide  
Electric Inductive Range  
PLANNING  
GUIDE  
All tolerances +1/16” (+1.6 mm), -0 unless otherwise noted.  
Failure to meet or exceed the maximum and  
minimum dimensions/clearances stated may result  
in a fire hazard.  
The shaded area shown denotes the location of  
the electrical junction box/receptacle. This is the  
suggested location. For replacement purposes, the  
location of the existing electrical supply may be  
utilized provided that it does not interfere with the  
sides or rear of the range.  
B
Access to the remote circuit breaker panel/fuse box,  
with the range in place and operating, must also be  
allowed for in the installation.  
The electrical junction box/receptacle must be  
ocated so that it does not interfere with the range  
n it is installed and under operation. In addition,  
ction box/receptacle must be located so  
can be removed for service and remain  
o power.  
13” (33.0 cm)  
max.4  
Non-combustible  
surface along  
back wall  
recommended  
the risk of burns or fire by reaching  
ed surface units, cabinet storage space  
above surface units should be avoided. If  
net storage space is to be provided directly  
bove the range, the risk of personal injury may be  
reduced by installing a range hood.  
Top of  
finished  
counter  
Note 1  
Suggest
In all instances, installation of a range hood is highly  
recommended. The hood should project horizontally  
a minimum of five (5) inches beyond the face of  
the cabinets. See the range hood specifications for  
minimum clearances.  
A
18” (45.7 cm)  
locati
min.4  
util
The range may be installed flush to the rear wall.  
See diagram and notes for rear wall surface  
requirements. It is not necessary to install non-  
combustible materials behind the range below the  
countertop height.  
Note 2  
Any openings in the wall behind the appliance or in  
the floor underneath it must be sealed.  
C
a*  
B
c
30 1/16” min.  
(76.4 cm)  
36” (91.4 cm) recommended  
30” (76.2 cm) min.  
37” (94.0 cm)  
max.  
* See the cutout dimensions on following page for self-rimming installations.  
FREEStANDING INStALLAtION cAbINEt cUtOUt DImENSIONS - mODELS RR30NS, RR30NFS, RR30NIS AND RR30NIFS  
130” (76.2 cm) min. vertical clearance from top of range grates to bottom of uncovered wood or metal cabinet. 24” (61 cm) min. clearance if bottom of wood  
or metal cabinets are protected by not less than 1/4“ (0.6 cm) flame retardant millboard covered with no less than No. 28 MSG sheet steel 0.015” (0.04  
cm) stainless steel, or 0.024” (0.06 cm) aluminum or 0.020” (0.05cm) copper. If installing range hood, check the hood specifications for minimum required  
clearances.  
2Cabinet/countertop depth is at discretion of customer but cabinet face SHALL NOT protrude further than rear of front panel. See Product Dimensions.  
3Consult local code and following pages for requirements.  
4This specification not applicable for cabinets more than a horizontal distance of 1” (2.6 cm) min from edge of range.  
51” (2.6 cm) min. to combustible sidewalls above range (both sides).  
All specifications subject to change without notice.  
Phone: (800) 793-0093  
RR30NS, RR30NFS, RR30NIS, RR30NIFS  
Document # PG05-009  
Revised 05/23/13 Page 4/5  
Renaissance 30” Wide  
Electric Inductive Range  
PLANNING  
GUIDE  
Cabinet Cutouts for Self-rimming installation (Models rr30niS and rr30niFS Only)  
All tolerances +1/16” (+1.6 mm), -0 unless otherwise noted.  
Countertop  
1 5/8 (41.1 cm)  
max. thickness  
Countertop height: 34 3/4” (88.3 cm) min.  
36 7/8” (93.7 cm) max.  
Countertop thickness: 1 5/8” (4.1 cm) max.  
(see diagrams)  
The self-rimming installation of the RR30NI[F]S range creates a  
“built-in” look where the range trim overlaps the countertop on both  
sides and in back.  
iMPOrTanT: When installing the range in this configuration,  
ventilation must be provided to allow for cooling of the ranges  
internal components. See diagram, left.  
34 3/4”  
(88.3 cm)  
to  
36 7/8”  
(93.7 cm)  
Observe all vecabinet clearances on page 3/5.  
Cut 3” dia. (7.6 cm) holes  
at back bottom of cabinet  
for ventilation.  
On self-rimions when sliding the range into position, it  
will stop he control panel or side panels contact the  
notce countertop.  
Provide ventilation through  
cabient both sides,  
7 square inches min.  
Location may vary.  
1” min. (2.6 cm)  
to any combustibles  
above counter both sides  
Rear wall or  
countertop edge  
3/8” min
counte
tOP vIEW - SLIDE-IN, SELF-RImmING INStALLAtION,  
3” SIDE PANELS INStALLED  
0”  
0.8 cm)  
to  
23”  
(58.4 cm)  
24 5/8”  
(62.5 cm)  
max.  
29 1/4” (74.3 c
countertop op
30 1/16” (
cabinet
below
Notch co
to width of c
Cabinet fac
below counterto
Countertop front  
1” min. (2.6 cm)  
Rear wall or  
3/8” min. (9.5 mm)  
countertop overhang  
to any combustibles  
countertop edge  
above counter both sides  
tOP vIEW - SLIDE-IN, SELF-RImmING INStALLAtION,  
3” SIDE PANELS REmOvED  
* To create a “built-in look” on the front of the cabinet, this  
dimension may be changed to 29 1/4” (74.3 cm), with the  
width at the notches remaining 30 1/16”. This configuration  
is only for models RR30NIS and RR30NIFS with side panels  
behind door removed.  
23”  
(58.4 cm)  
24 5/8”  
(62.5 cm)  
max.  
29 1/4” (74.3 cm)  
countertop opening  
30 1/16” (76.2 cm)*  
cabinet opening  
below countertop  
Notch countertop  
to width of cabinets  
Cabinet face  
below countertop  
Countertop front  
All specifications subject to change without notice.  
Phone: (800) 793-0093  
RR30NS, RR30NFS, RR30NIS, RR30NIFS  
Document # PG05-009  
Revised 05/23/13 Page 5/5  
Renaissance 30” Wide  
Electric Inductive Range  
PLANNING  
GUIDE  
Cabinet Cutouts for Self-rimming installation (Models rr30niS and rr30niFS Only)  
All tolerances +1/16” (+1.6 mm), -0 unless otherwise noted.  
Countertop  
1 5/8 (41.1 cm)  
max. thickness  
Countertop height: 34 3/4” (88.3 cm) min.  
36 7/8” (93.7 cm) max.  
Countertop thickness: 1 5/8” (4.1 cm) max.  
(see diagrams)  
Trim kit PN ATKR30SR is required for proper installation of a raised  
vent with this range.  
The self-rimming installation of the RR30NI[F]S range and ERV30[15]  
raised vent create a “built-in” look where the range trim overlaps  
the countertop on both sides and the raised vent trim overlaps the  
countertop in back. The ATKR30SR trim kit, installed on the back of  
the range, will cer the front of the raised vent chassis.  
34 3/4”  
(88.3 cm)  
to  
36 7/8”  
(93.7 cm)  
iMPOrTanstalling the range in this configuration,  
ventilatioed to allow for cooling of the ranges  
internagram, left.  
Cut 3” dia. (7.6 cm) holes  
at back bottom of cabinet  
for ventilation.  
Oarances on page 3/5.  
Provide ventilation through  
cabient both sides,  
7 square inches min.  
Location may vary.  
configuration is required for raised vent  
ons with a raised vent, when sliding the  
will stop when the rear of the control panel or  
ct the notches toward the front of the countertop.  
1” min. (2.6 cm)  
to any combustibles  
above counter both sides  
Rear wall or  
countertop edge  
3/8
c
(6.7 cm)  
27 1/2” (69.9 cm)  
raised vent opening  
tOP vIEW - DOWNDRAFt ERv30[15] WIth  
SLIDE-IN, SELF-RImmING INStALLAtION,  
3” SIDE PANELS INStALLED  
20 3/8”  
(51.8 cm)  
to  
23 3/8”  
(59.4 cm)  
25”  
(63.5 cm)  
max.  
cm)  
29 1/4” (
countert
30
c
b
Notc
to width s  
Cabinet
below countertop  
Countertop front  
1” min. (2.6 cm)  
to any combustibles  
above counter both sides  
Rear wall or  
countertop edge  
3/8” min. (1.0 cm)  
countertop overhang  
2 5/8” (6.7 cm)  
27 1/2” (69.9 cm)  
raised vent opening  
tOP vIEW - DOWNDRAFt ERv30[15] WIth  
SLIDE-IN, SELF-RImmING INStALLAtION,  
3” SIDE PANELS REmOvED  
25”  
(63.5 cm)  
max.  
23 3/8”  
(59.4 cm)  
29 1/4” (74.3 cm)  
countertop opening  
30 1/16” (76.2 cm)*  
cabinet opening  
below countertop  
* To create a “built-in look” on the front of the cabinet, this  
dimension may be changed to 29 1/4” (74.3 cm), with the  
width at the notches remaining 30 1/16”. This configuration  
is only for models RR30NIS and RR30NIFS with side  
panels behind door removed.  
Notch countertop  
to width of cabinets  
Cabinet face  
below countertop  
Countertop front  
All specifications subject to change without notice.  
Phone: (800) 793-0093  

HP Hewlett Packard d8905 User Manual
Diamond Multimedia XtremeTV PVR 550RC User Manual
Diamond Multimedia XtremeTV HDTV 110 User Manual
Diamond Multimedia Radeon S120AGP128 CN User Manual
Cobra Electronics CP 2501 User Manual
Cleveland Range ConvectionPro Steamers 36CDM16 User Manual
BT 5310 User Manual
BT 3000 Classic User Manual
Black Box LH1506ALH1508A User Manual
AMD Geode SC3200 User Manual